Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi all,
Im testing the "periodic_advertising_example" but in wireshark (nrf52840 dongle) I can just receive the AUX_ADV_IND packet below. I can I see the periodic advertising...
Application: Matter product using nRF54L15, SDK 3.0.0
Ecosystem: Matter product joins Apple HomePod
I am not able to get time/date delivered via Matter to the product...
What are the implications of doing this in one of the Kconfig files in one of my modules? should this override the first configuration of NFCT_IRQ_PRIORITY? from my undersanding...
I’m working on DFU using the BLE Mesh distributor and target sample codes. I built both with Sysbuild and flashed them onto two separate nRF52840 boards. The target board...
Hai,
We are developing a product having nrf54l05. I'm using nrf connect sdk for programming. I'm using one GPIOs for input. I have enabled pullup for that pin. We want to...
1. development environment:
software ncs3.0.1 , DW3xxx_XR6.0C_24Feb2022, vscode
hardware: nrf52840, DW3210
DW3210 is a UWB chip produced by Qorvo, and its corresponding...
Hello
I have just received thingy:91 x to start learning nrf platform. Unfortunately it's not all smooth. I am trying to do flash Blank application. It builds fine but then...
hi support team,
i have close this ticket:
but i need open this ticket and ask how to program 9151 externa; spi flash.
i don't know if 9151 json file is correct and...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Here’s what to check next for toolchain detection issues in VS Code with nRF Connect SDK:
1. nRF Connect Extension Output In VS Code, go to View → Output. Select nRF Connect...
Hi The Nordic Team,
I am developing a SED device of Matter over Thread. How can I get the ipv6 address of my parent node after my device is connected to the network?
...
This is our first time using TC2050 for the smaller footprint in our prototype. But we can't establish a connection with JTAG in nRG Programmer.
Below is the log from...
SDK: NCS 3.0.2
Part: NRF52840
I am running the NRF52840 as an HCI controller over SPI. I can advertise and connect. However, I need to advertise while connected and support...
