I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hello,
I using ncs v3.1.1 SLM on nrf9151 to send messages to a CoAP server. It seems nrf9151 by default uses AES_128_CBC_SHA256 even though on the server side, we have given...
I measured the power consumption of the BLE RX using the nRF54L15.(nRF54L15-DK v1.0.0) 3.0V operation apps: scan_adv (delete advertising) west build -b nrf54l15dk/nrf54l15...
Hello,
Working on Ubuntu 22.04 with nRF Connect SDK 2.6.1 for the target nrf5340dk_nrf5340_cpuapp_ns (= with TF-M).
My application image became too large. I want to split...
Hi，
ncs v3.2.0，nRF54LM20-DK， I drive a buzzer. When the buzzer doesn't ring, I need a low level. I tried it according to the following method. I can't output a low level...
I need to generate PWM siganl around 4 mhz frequency but i did not get proper pwm signal and i got only millivolt range voltage this issue cuase i did not get proper audio...
Hello, I am developing with nRF5340 with my custom board. I observed a high current consumption when the network core is flashed with the ipc_radio image. I am developing...
Hi,
I am using NCS v3.3.0 and would like to implement the following setup:
Central: nRF52840 Dongle (connected to PC via USB)
Peripheral: nRF52833 acting as...
Hi Team,
Whether there is any configuration or option available to disable/eliminate signature verification during the boot process.
If disabling is not recommended...
HI
I need to implement LE Audio and voice KWS (Keyword Spotting). The microphone input needs to use two microphones to perform noise and sound filtering for sounds that...
Hello Team,
I am trying to configure pwm channel to a gpio in nRF54LM20B DK. I am not able to generate output using pwm channel. I have understood that here dts nodes...
The DECT Nr+ shell (the MAC version, not the -phy; tested with v3.3.0-ba167d9f3db4) offers IPv6 connectivity.
The DECT standard has a profile for IPv6 described in ETSI...
I wrote a simple terminal that reads the keyboard input from USB UART device and echos it back to the same device. It works as follows: 1. It registers an interrupt handler...
Working application, using S132 SoftDevice, new variation of the application. Using UARTE, with P0.12 assigned as RxD. Something in the SoftDevice is grabbing P0.12 and setting...
