I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
I have a question about SPIM. Is it possible to have two events via DPPI that will start different SPIM transfers for the same SPIM channel?
What would happen if a...
I have the board: NRF52840-DK PCA10056 3.0.3 2026.5 1050266921
Is it possible to use OB J-Link to debug STM32/RP2040 MCUs connected to P19/P20? Or OB J-Link support limited...
We are using CMakePresets.json extensively in our project and rely on the condition field to control which presets are visible depending on the host system.
However, it...
Hello,
We are using the nRF52840 with SDK 17.1.0, SoftDevice S140 v7.2.0, and the secure bootloader (nrf_bootloader.c).
Our application relies on reading NRF_POWER->RESETREAS...
Hi there,
One of the functions of the DECT MAC layer is to allocate radio resources to RDs. According to the standard, the MAC layer does that using special beacon messages...
Hi,
I'm working on a wireless sensing project using the nRF54L15-DK (PCA10156) where I need continuous RSSI measurements at 2440 MHz. I'm accessing the RADIO peripheral...
Hi,
I am working on an nRF52832 using nRF5 SDK 16.0 and I am seeing inconsistent behaviour in the RESETREAS register. During a power-on reset, the value is usually 0 but...
Hi!
We are building an application for Thingy91X and noticed that there is an overlap between the shared memory between the app and net mcus, sram0_shared, and RetainedMem...
Hello, I am working on a project using nRF52832 with Zephyr RTOS (NCS v2.7.0) and MCUboot. I have implemented BLE passkey-based security (BT_SECURITY_L3) on the device. I...
I bought an NRF52833 DK development board. I want to conduct an AOA experiment, but I don't have an antenna array. I was told that I can find the schematic and PCB files for...
I have been trying to understand how the controller manages the interleaving when used for broadcast / auracast. I have been experimenting with the samples from zephyr called...
Hi,
We are evaluating the nRF7002 for a custom built Wi-Fi device. Is there a way by e.g. copying your reference/dk design reducing the scope of the regulatory testing?...
When is the anticipated release date for the commercial ready NTN functionality of the NRF9151? I am specifically looking for all Nordic supported Github projects and documentation...
Hi,
I just received two new nRF54LM20-DK boards and wanted to run a Matter quickstart demo. Unfortunately, it’s already failing during programming. What could be cause of...
