Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
Hello everyone,
I need to save a core dump on my NRF54L15 internal flash in order to debug an issue. I've been following the "Debugging and Troubleshooting section" of the...
Hi everyone,
I am facing an issue when modifying the peripheral_nfc_pairing example.
Due to hardware limitations, my device cannot integrate an NFC antenna. Instead, I...
Hello. We are evaluating the nRF9151 SiP as a potential solution due to its low power consumption and compact form factor . However, our team has limited experience with firmware...
Hi,
I'm considering the implementation options for nRF91 GPS front end. Having a shared antenna for LTE and GPS would be tempting, but I'm concerned about the filtering...
Hello,
I am trying to get some basic examples working with my new NRF9151DK and running into quite a few issues. Note that this is using a onomondo sim card that came with...
Hi,
With NCS v3.1.0 and Nordic's downstream zephyr ncs-v3.1.0, I got build failure with following message:
--
warning: attempt to assign the value 'n' to the undefined...
Hello Nordic team,
After many hours I have not been able to get socket dispatching working with Zephyrs MQTT client, and I am not sure how to proceed.
First of all I would...
Hi Support Team
Due to there is very little space of C: drive of computer, so I moved the NCS SDK from C: drive to D: drive. The VS code can't recognize the SDK and toolchain...
There are 100s of solutions on the zephyr git and the nordic git. It took me a while to understand it all and it took me hours of debugging and frustration before I ended...
I want to work with the nRF Connect Plugin for VS Code and my nRF52840 DK with Zephyr. I created a new application from the "nRF Connect" plugin and selected the hello world...
Hello,
I perform a test using a nrf52840 DK board in order to output a PWM at 50 Hz on a GPIO.
Here is the code:
void pwm_init(void) { nrf_drv_pwm_config_t const config0...
Dear Nordic-Support,
have a question regarding nrfutil and the offline package generation, described here: https://docs.nordicsemi.com/bundle/nrfutil/page/guides/installing...
I am evaluating Curve25519 performance on the nRF5340 and have observed that the following operations each require approximately 2.5 seconds to execute:
- `wc_curve25519_make_key...
My customer had ttothis question:
We recently purchased and use your Nordic Power Profiler PPK2 at my company. Does this device come with any calibration certificates? How...
