Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
I have a 2 Mbit EEPROM, normally I would configure the overlay as follows:
But the M24M02 eeprom uses 4 addresses to access 4 blocks of memory within the device, 50, 51...
Hello
I've juste came back from holidays and I no longer can do pristine build on my applications (no matter which toolchain or SDK I am using). When I do pristine build...
Hi,
I'm not sure if this is the correct place to report this, but it was not possible for me to report this on the nrfx GitHub page.
I found out that the function nrfy_nfct_...
I'm using nRF Connect SDK V2.7.0 and want to achieve coexistence between Zigbee and IEEE 802.15.4 physical layer on the same Soc. Is it possibel to enable the MPSL feature...
Using nRF Connection SDK v3.0.2 and nRF Connection SDK Toolchain v3.0.2
Create a new blank application, "Add build Configuration" for nrf54l15dk/nrf54l15/cpuapp/ns then...
Steps Taken:
Followed the official Nordic guide for adding DFU support to Thingy:91.
Built the project successfully using west build .
Tried flashing via...
Hi all,
Full debug builds ( -Og ) of lwm2m_client simply don’t fit into the nRF91xx targets (nRF9151 DK, Thingy91, Thingy91x). As a workaround I found that building with...
Hi There,
I'm following the "nRF Connect SDK Fundamentals" to set the environment up. The device I'm using is nRF52 kit with N52832 MCU and PCA10040.
The USB wire is works...
Hello,
I am following the official Nordic Academy nRF Connect SDK Intermediate course , specifically Lesson 9 – Bootloaders and DFU/FOTA, Exercise 5 (FOTA over Bluetooth...
Hi,
I’m using the Thingy:91X board with the nRF9151 chip, modem firmware version 2.0.2, and SDK version 2.9.0.
We’re encountering a serious issue: the modem does not reconnect...
Hi, I am no longer able to download the nRF5 SDK version 16.0.0_98a08e2 using curl . A few weeks ago it worked fine, but now I can only download the .zip file through a browser...
I'm using the nRF9160DK as a BLE-to-LTE bridge, and I have the onboard 52840 configured as my Bluetooth controller. The 9160DK advertises as a peripheral and waits for a connection...
“Why, after setting up the custom board and writing CONFIG_BOARD="my_custom_board" in prj.conf, do I encounter the errors: message(FATAL_ERROR "command failed with return...
I was hoping to access content from DevZone and DevAcedemy content from NotebookLM to combine with my private documentation so I could ask questions specific to my device...
I have been developing software, embedded systems, and hardware for over 30 years, and I must admit: working with nRF Connect + VSCode on Windows (both native and via WSL...
