Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi!
I am using the nRF52832 for a small custom PCB for a wearable device and I would appreciate a review from the experts, before proceeding with manufacturing :)
The...
Hi,
I have a FAT file system that I use with an USB Mass Storage feature. I use the mx25r64 NOR flash (the same as the nrf7002dk evalboard). I am working on ncs 3.0.2. ...
TLDR:
I'm working on getting LE Audio working on a Raspberry Pi CM4 setup and running into some frustrating issues. I've got a u-blox NORA-B126 module (with the nRF5340...
Hi nordic engineer
I have a product use nrf52832. And have two project,project use nrf5 17.0.0 SDK and MDK.
The project A choose chip nrf52832 and S132
The project B...
Hi
The nRF54L15-DK suite tests the accuracy of channel sounding, all ncs versions are v3.1.1. I am using the channel_sounding_ras_initiator and channel_sounding_ras_reflector...
Hello,
At my company, I am working on a board with an nrf54L15, equipped with an SX1261 and an ADC MCP3461R.
I started development with SDK 3.0.2 and everything is working...
Hello!
With nRF52, nRF5 SDK and SoftDevice S130, we were using some of the Radio's PPI events (e.g. EVENT_END) for some functionality.
Now we plan to move to nRF54L and...
When running the channel sounding example on the nrf54l15, how can one obtain the IQ values of the ranging signal?I want to obtain the IQ value and then use my own algorithm...
Hello,
I have tested a thread network with a nRF52840 SDK programmed with Thread COAP Client sample and two nRF52840SDK programmed with Thread COAP Server sample.
All...
I've built a project based on the peripheral_uart appliction. This is working well, but I need to now sort out the lowpower mode. My product is battery powere & I need to...
I’m using the nRF54L15 to test throughput. I want to connect a single board to any arbitrary BLE device to test GATT throughput. Is there any way to do this? Are there any...
I want to use the UART20 serial port to map to other pins for easier PCB layout, but when I use the NRF54L15，
overlay config
my main code but no printk or printf What...
Hi,
I’m using the nRF52840 for BLE packet capturing, including security-related exchanges. However, during analysis in Wireshark , I’m unable to see any SMP (Security Manager...
Hi There,
I have integrated ble_app_hrs and saadc module on nrf52840 dev kit, it compiled without errors. while debugging it is stuck in - saadc_sampling_event_init(), ...
I don't see how we can send 'conn param update request' rejection. I am getting BLE_GAP_EVT_CONN_PARAM_UPDATE_REQUEST and there is way to update the conn params using sd_ble_gap_conn_param_update...
