I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
My task is to implement inbuilt RTC for nordic MCU nrf54l15 series. When i use the below API nrfx_grtc_init, it is throwing a error and returning a error code which is saying...
Hello Nordic Support Team,
I’m working with an nRF5340 using nRF Connect SDK 3.0.2.
I am trying to use the NFC pins (P0.02 and P0.03) as an I2C slave interface. However...
Hi,
I would like to generate a PWM signal specifically on the P0.03 pin of the nRF54L15 using GPIOTE + DPPI + TIMERS.
As far as I’m concerned, Port 0 in nRF54L15 does...
Hello all,
I am trying to run bap_unicast_server example with nrf5340_dk. I used no sysbuild configuration. Then I manually added hci_ipc as it shown at ss
I flashed succesfully...
Hi,
I'm currently working on a project using the nRF5340, and I've successfully configured the I2C0 interface as a static Master in my .overlay file using the following...
Hi all,
I am trying to execute an application in XIP mode from an external QSPI flash on an nRF device (nRF5340, Zephyr + MCUBOOT). The setup is:
Partition file:pm_static...
Hello,
I am using edge impulse library to achieve on-device classification. I now want to put the edge impulse related code to the external flash and use XIP function there...
Dear All, I am facing a rather strange issue with the nrf/samples/wifi/shutdown example. I am working with nRF Connect SDK v3.1.1 and a nRF7002DK board. I am observing the...
I recently upgraded from a Ubuntu raspberry to a Raspery PI5 running PI OS and have two Nordic boards but not able to install the nrfConnect image on the PI image. Is there...
Hello,
We are preparing nrf52832xxAA for certification, Im trying to compile DTM from nRF5_SDK_17.1.0 (same issue on v16.0) Default UART pins run fine without error #define...
Hi, I am trying to migrate my device from s132 7.2.0 to s332 7.0.1, for adding ANT. I have no more access to the SWD. I know it is not tested : docs.nordicsemi.com/.../lib_bootloader_dfu_validation...
I am attempting to integrate the MM8108 with the NRF54L15 SoC as my lead engineer suggested, but now I am finding that it is not that straightforward. We want to make a HaLow...
Dear All, I am developing an application where I need to get the nRF5340 to the low power state, where the chip is consuming less than 10uA when it idle, while using the nRF7002...
I would like to control the RGB LED on the board. I followed the drievr example provided by the nrf sdk, but it doesn't work. As far as I understand, I don't need the signal...
