Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
I am trying to retrieve the PIN / HWID required for nRF Cloud onboarding using the AT command AT%XDEVICEID , but I am unable to get a valid response from the modem.
However...
Hello,
I have downloaded the newest Zigbee R23 SDK (v1.3.0).
When I use the feature inside VS Code: "nRF Connect" -> "Create a new board" to create my custom board...
Only information I can get back for the nPM1304 datasheet from Nordic's website is an html version that's missing all the normal sections you expect in a datasheet. Things...
Hi,
I'm designing a battery-powered active RFID timing base station and I'm evaluating the nRF54L10 for it. Patrick from Nordic suggested the nRF54L series over the older...
Dear Nordic Support teams,
About the NRF54LM20A-CAAA_CSP61,
Could you provide the CSP61 package library or related information? Our customer is requesting it.
Thanks...
Enabling CONFIG_USE_SWITCH=y causes usage fault on nRF54L15 with nRF Connect SDK v3.4.0-rc1.
Where it crashes: Context switch on interrupt exit, Zephyr arm-m-switch.c :...
Subject: nRF52833 - OpenOCD ST-LINK MEM-AP Access Failure During Flashing
Hello Nordic Support Team,
I am working with an nRF52833 module and trying to flash firmware...
Dear Support,
I'm using nCS v3.1.1 and the Matter example project. Could you please provide a simple example showing how to use GPIOTE + DPPI + TIMER capture?
My goal...
i am currently working on a board that is using the nrf54l15 chip. and when CONFIG_BT=n or just not included in the prj.conf i see a power consumption of about 80uA on the...
Page 399 of nRF54L15/nRF54L10/nRF54L05 Datasheet v1.0 shows:
CLK = PCLK32M/(2*PRESCALER)
but this formula does not match the values in the examples in Table 46.
I CAN...
Hello Nordic-Team,
I am using the SENSING mechanism on GPIOs to wake up a firmware from SYSTEM OFF. Two GPIOs are used for this and it is crucial for the firmware to detect...
Hi,
I am using bare metal SDK v1.0.0. On my prototype, I want to use BLE softdevice together with SPIM20 peripheral, physically connected to Port 2. Starting from the BLE...
Hi, The docs, at least for the nrf54L series, cannot be access because the 'site is under maintenance'. The following links don't work: https://docs-be.nordicsemi.com/bundle...
