We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello Team,
I am new to nordic products. We have just purchased Thingy: 91x from you.
I just want to explore on nRF52840 BLE section. I was not able to detect the device...
Hello! I have 126 kB MCUboot partition which I'd like to make immutable (write protected so it can't be corrupted). I have serial-recovery, KMU key handling, debug optimization...
When building applications/hpf/gpio with -DSB_CONFIG_HPF_GPIO_BACKEND_ICMSG=y on nRF54L15 DK (NCS v3.2.4), the build fails with error: '__device_dts_ord_DT_N_NODELABEL_ipc0_ORD...
Dear DevZone Team
To detect possible TWI slave devices connected on a TWI bus, we want to scan for device addresses and check if they are being acknowledged.
In the twi_scanner...
When a BTLE Connection is underway, calling bt_disable can result in an infinite hang in the Zephyr BTLE stack. Using ncs v3.0.0 Any ideas? There is some mention of: CONFIG_BT_HCI_ACL_FLOW_CONTROL...
I have implemented the erase protect and app protect in our application. There are commands for locking and unlocking the device. Actually, during testing I was able to lock...
Hello Team,
I am working with Thingy: 91x and I have searched your websites for Schematic for some understanding purpose used in Thingy: 91x Kit.
But I couldnt find any...
Hello, I started working with the nRF Cloud and have been trying to understand the authentication procedure. From my understanding, the create_credentials script creates the...
Greetings, my name is Toni. We are trying sending the MO PS SMS-over-CP/NAS or IMS from the nRF9160-DK: - Hw rev2, - mfw v1.3.7, - NCS prebuilt apps from the v2.3.0 and v3...
Hi Nordic team,
I am designing a new board from scratch around the nRF52832 in KiCad.
My current plan is to use the nRF52832-QFAA/QFAB QFN48 package on a 2-layer PCB....
Hi,
Using the Matter template sample, I'm not able do to the commisionning until the end because I got an error saying " an error occured" on my border router( using an...
We are currently developing a nrf52840 firmware which should support RSCP as collector.
Setup:
nrf52840
ncs2.9 with
Q322804 NCS Host
Q331587 SoftDevice Controller...
Hello,
I have been trying to find an answer to this in the documentation but have thusfar been unsuccesful. For our use case we use the Certificate management part of the...
After Can the ESB protocol be added to the nrf desktop routine? . I tested the code for switching from ESB to BT (Non-Concurrent)。
The SDK version I used is V3.2.0. The...
Hi,
I'm looking for any help to implement wifi OTA for nrf54l15, found a lot of docs about FOTA for upload firmware over ble but i need to upload the firmware located at...
