But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
So my board uses uart00; I also need to use ZMS for storing configuration data.
If I try to compile with no SPI enabled the Flash drivers throw an error '__device_dts_ord_130...
under freestanding applications, which code to use to enable bluetooth on nRF52840 DK kit . Then, it has to pair with android mobile. how i can achieve it.
Hello,
I am configuring the Watchdog Timer (WDT) on my custom device and observed that it gets disabled when the system enters Deep Sleep mode. This behavior prevents the...
Hello Nordic Support team,
I'm receiving the Transmission failure and Lora Initialisation failed message despite to correct wiring and everything else. I'd attach a link...
I've been trying to get SPI slave running on the NRF54L15-DK for over a week. I am new to Connect SDK but have successfully completed this task with NRF52840-DK (and dongle...
I changed the file, C:\Users\kruenheck\AppData\Roaming\nrfconnect-bluetooth-low-energy\uuid_definitions.json so that it has a new service:
{ "_comment": { "comment": [ ...
I am programming with nrf52833,ncs v2.9.0.Based on peripheral_hid_keyboard and cetral hid.
I send about 6k hid keys to central via ,while sending,peripheral side
But ERR...
Hi Nordic team,
I’m trying to use my nRF9151 DK as a Bluetooth Host (Zephyr) connected over UART (H:4) to an external Seeed XIAO BLE board (acting as the Controller). My...
Hi,
We have functioning application code under the 2.4.4 SDK development setup. I would like to start migrating to newer code but am encountering issues. (Ultimately, I...
I have an nRF5340 DK (not audio DK), and I want to send LE audio from my LE audio compatible device to my DK and then have my DK play that audio over I2S to my external amp...
Hi there, I-m trying to compile a hello world sample with an encrypted bootloader
# Sysbuild configuration file.
#see C:\D\dev\nordicsemi\v2.7.0\nrf\doc\nrf\releases_and_maturity...
Hi all,
I'm currently facing the issue that we are receiving a PKCS7 encoded response from our EST server via a `/simpleenroll` request.
The PKCS7 response now has to...
We have a locator-beacon setup based on this https://docs.nordicsemi.com/bundle/ncs-2.9.1/page/nrf/samples/bluetooth/direction_finding_connectionless_tx/README.html running...
I have been facing a persistent Zephyr CMake/Kconfig build failure in my nRF Connect SDK setup.
Environment: Windows, nRF Connect SDK v2.7.0 , Toolchain v2.7.0 , using VS...
