Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Environment
SoC: nRF54LM20A (cpuapp, non-secure / TF-M)
nRF Connect SDK: v3.3.0
sQSPI soft peripheral driving an AMOLED display via the FLPR
BLE active via MPSL...
Hi team,
Please find below logs. While programing this error occurs. please find the logs and do needful. Earlier programing happens now it's not happened. Based on below...
I have an application with a shipping mode that when enabled/disabled calls `conn_mgr_all_if_connect/conn_mgr_all_if_disconnect`. These functions eventually end up in `lte_net_if...
Hi,
While testing, I ran into multiple problems when measuring the current consumption with the PPK 2 on the nRF52833 dk.
For all measurements the Blinky + Bluetooth demo...
Hello,
I am using WM02F WiFi mdule with nRF7002 SoC and i am having some issues with the TX power measurement of the WM02F WiFi module while operating it in 2.4GHz.
I...
Dear Nordic team,
We are a medical device manufacturer company in Australia.
Currently we are developing a medical device system, the system compose of a base station...
In developing project firmware uses bluetooth shell and one command outputs many lines.
It works fine. Unfortunately, firmware locks up after phone BLE app disconnect in...
Hello, we want to evaluate the BLE ISP2454-LX chip.
To do this we bought from RUTRONIK FRANCE an ISP2454-LX-EB evaluation board with the ISP2454-LX-TB test board.
SDK...
Hello,
We are currently evaluating BLE Gateway (CIS, BIS) development using the nRF5340 Audio DK.
We would like to ask whether bidirectional CIS streaming is officially...
I am using nRF54L15-DK, I choosed the CONFIG_NFC_T2T_NRFXLIB=y.
In this case, I get tag type ISO 14443-4.
But what I need is ISO 14443-3A.
The following is my nfc_init...
Hi,
I'm developing with NCS 3.2.4 and want to expose the Zephyr shell over BLE using NUS (Nordic UART Service). I've identified two possible starting points and have a couple...
Hello, we want to evaluate the BLE ISP2454-LX chip.
To do this we bought from RUTRONIK FRANCE an ISP2454-LX-EB evaluation board with the ISP2454-LX-TB test board.
SDK...
Hi,
I see the different behavior of the function sd_ble_gap_conn_param_update when connected to Windows integrated Bluetooth.
Using bare-metal SDK v0.9.0 it succeeds...
Dear Everyone, SDK 3.3.0, Board: NRF54L15 We have integrated MCUBOOT into our project. We have image built for two slots and we can see that it works once uploaded by VS-Code...
