Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
I am using an nRF5340 DK (PCA10095) running the direction_finding_connectionless_tx sample from nRF Connect SDK v3.3.1 as a CTE transmitter for a Bluetooth AoA direction finding...
I compiled some legacy code (once written for the nRF52832), trying to adapt it for the nRF52805.
I have already done the following:
defining -DNRF52805_XXAA
defining...
Yesterday, I upgraded to nRF Connect for VS Code extension version 2026.6.2030 and restarted VS Code, and now no matter what I do, the 'Flash' button in my project just pops...
We use the NRF Mesh Android Library (and are developing with iOS version as well). An issue that we are running into on a small number of devices is that the library things...
Can I reduce the thermal pad size for the nRF52840 (aQFN)?
Currently the thermal pad is 4.85mm x 4.85mm, but in order to facilitate breaking out all the inner pads, reducing...
The nrf_cloud_multi_service sample sometimes appears to hang(appears to be a deadlock) shortly after successfully connecting and authorizing with nRF Cloud.
The log consistently...
Hi,
I am trying to program a custom board containing an nRF9151-LACA using the external programming interface (P20) on an nRF9151 DK. The board has never been programmed...
Hi --
We are in the process of setting up to flash a few hundred devices for our internal testing. We can currently flash to our board using nrfjprog either directly from...
I have a eval setup where I use the nrf52840 dongle with hci_usb flashed. It has a non-default config to enable DLE (this works fine).
I am sending buffers of 8192 bytes...
Hello,
I'm looking to get XInput working on the nRF52840 so that our device can appear as an Xbox-compatible game controller. I'd appreciate any guidance or recommendations...
Hi,
I have an application which is developed using nRF5 SDK version 17.1.0
Migrating to nRFConnect SDK is not an option at this stage of the project.
The application...
I'm stuck trying to set my nRF Connect extension on VSC. I've followed the guide for the installation but I'm reaching a wall. Every time I try to install a given SDK I have...
Hi all,
I am currently testing on nrf52dk (PCA10040, 3.0.0) with NCS v3.3. Note: I also tested with vanilla Zephyr and see the same issue.
The code I run is to 100% the...
Hello,
I previously opened a ticket describing an issue where using MCUBoot in NCS v3.1.0 caused the GRTC to reset after a sys_poweroff() .
As discussed in that ticket...
Hi everyone,
I'm evaluating the nRF54L15 for a very low-power sensor node application powered by a Lithium Thionyl Chloride (Li-SOCl₂) primary cell. The goal is to achieve...
