I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
Hello,
I am trying to exchange data with an external slave sensor via SPIM communication using the nRF5340DK.
I am currently facing two main issues:
1. The spi_transceive...
I am using the NRF54L05.When I was using the timer function of the Zephyr software, I created a timer with a 10ms cycle. After my system had been running for a long time ...
ncs: v3.2.0
chip: nRF54L15
If I set CONFIG_PM_PARTITION_SIZE_MCUBOOT=0x10000 (64K), MCUboot fails to boot, and the error displayed is: 'Protect mcuboot flash failed...
Hi,
Can you please guide me if I want to receive a larger message of around 15KB from server, how can I do it using CoAP block transfer in thread.
I am using nRF5 SDK...
Hi,
I built the nrf/samples/bluetooth/hci_lpuart program in SDK v3.1.1. I am using an nRF9160DK board version 1.1.0. I did add several printk statements to zephyr/samples...
Hi Team,
We are working on a commercial pre-production project using nRF5340 and are currently migrating from nRF Connect SDK 2.6.1 to NCS 3.1.1 . We followed the official...
I have several hardware pieces based on the Fanstel WM02C nRF7002 module (nRF54L15 host) and am having problems connecting to WiFi networks on a subset.
All modules successfully...
nRF54L15, Zephyr +MCUboot. I am unable to redirect LOG_INF() output to RTT.
prj.conf
Can you tell me what is wrong? How to force logger to output to RTT?
I get error provisioning key on nRF54L15 and NCS 3.0.1. I tried using "Erase all" in nRF connect SDK Programmer, but it doesn't help. Please check also the attached log. nrf54l15dk...
We are trying to pass interrupts at high speed (clock signal) running at 800khz from port p1 to signal the RISC-V Co-processor to trigger a capture on a 4 bit bus. Is it possible...
Hi,
using nrf connect sdk 3.11, nrf54L15-PDK
I am testing low power with development board, I am trying to reach low power 2.9uA as bench marked.
When GPIO (button)...
I noticed in SD7 SDK16.0.0 when CENTRAL and PERIPHERAL connections are defined, the soft device will return designated central and peripheral connection handles. For example...
Hi,
We are modifying our existing product and adding PA to increase the range. Device right now is developed with nrf5 SDK, but we have plans to move to NCS. However manufacturer...
hi support team,
customer is using our 54L15 for mesh lighting project, here are three questions:
1.
customer needs timer model, i see the "time_cli.c" and "time_svr...
I'm developing for a custom board that has an nRF52832 and an FM25W04 external flash. My application uses nRF Connect SDK v2.9.2. I have a debug build that doesn't use a bootloader...
