I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hello Nordic Support Team,
I’m working with an nRF5340 using nRF Connect SDK 3.0.2.
I am trying to use the NFC pins (P0.02 and P0.03) as an I2C slave interface. However...
Hi,
I would like to generate a PWM signal specifically on the P0.03 pin of the nRF54L15 using GPIOTE + DPPI + TIMERS.
As far as I’m concerned, Port 0 in nRF54L15 does...
Hello all,
I am trying to run bap_unicast_server example with nrf5340_dk. I used no sysbuild configuration. Then I manually added hci_ipc as it shown at ss
I flashed succesfully...
Hi,
I'm currently working on a project using the nRF5340, and I've successfully configured the I2C0 interface as a static Master in my .overlay file using the following...
Hi all,
I am trying to execute an application in XIP mode from an external QSPI flash on an nRF device (nRF5340, Zephyr + MCUBOOT). The setup is:
Partition file:pm_static...
Hello,
I am using edge impulse library to achieve on-device classification. I now want to put the edge impulse related code to the external flash and use XIP function there...
Dear All, I am facing a rather strange issue with the nrf/samples/wifi/shutdown example. I am working with nRF Connect SDK v3.1.1 and a nRF7002DK board. I am observing the...
I recently upgraded from a Ubuntu raspberry to a Raspery PI5 running PI OS and have two Nordic boards but not able to install the nrfConnect image on the PI image. Is there...
Hello,
We are preparing nrf52832xxAA for certification, Im trying to compile DTM from nRF5_SDK_17.1.0 (same issue on v16.0) Default UART pins run fine without error #define...
Hi, I am trying to migrate my device from s132 7.2.0 to s332 7.0.1, for adding ANT. I have no more access to the SWD. I know it is not tested : docs.nordicsemi.com/.../lib_bootloader_dfu_validation...
I am attempting to integrate the MM8108 with the NRF54L15 SoC as my lead engineer suggested, but now I am finding that it is not that straightforward. We want to make a HaLow...
Dear All, I am developing an application where I need to get the nRF5340 to the low power state, where the chip is consuming less than 10uA when it idle, while using the nRF7002...
I would like to control the RGB LED on the board. I followed the drievr example provided by the nrf sdk, but it doesn't work. As far as I understand, I don't need the signal...
