Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
I am trying to run the WiFi Station sample, unchanged on a nrf7002DK, but receive the following error: "wifi_supplicant: Failed to add iface wlan0" Complete output as follows...
I’m currently experiencing an issue while trying to install the Toolchain Manager application from nRF Connect for Desktop (v5.2.0) on Windows 11.
Every time I attempt to...
Setup
Hardware: Nordic nRF7002DK as Wi-Fi STA (client) .
AP & Receiver: a Linux PC creates a Wi-Fi Hotspot/SoftAP (NetworkManager/hostapd) and simultaneously runs...
I’m having an issue using QSPI flash with NRF Connect SDK 3.1.1. I have two PCB versions with nRF52840 MCUs — one uses the W25Q128JVEM chip and the other uses the W25Q128JVPIQ...
I want to connect a W25Q01JVZEIM (128MB) NOR Flash ROM to SPI3 of the nRF52833 and implement USB MSC functionality. However, the build fails. It seems the overlay description...
I'm communicating to the nPM1300 eval kit over I2C from an nRf52833 DK (running a fuel gauge application). This works well until I connect PowerUp (through USB) and enable...
Hello to everyone!
I bought nRF54L15-DK for Matter Over Thread developing and prototyping.
Before nRF54L15 I tried ESP32C6 XIAO + Arduino IDE and it worked but it was...
Hey, I have an nrf52840, with lis2dh sensor.
I configured the sensor using the devicetree using the following code
and I change the sensetivity and some other register...
Hi all
I am very new to BLE development and I hope that this question was not asked before in another way.
Is this example also available in nRFConnect with another name...
I'm using an nRF52840 microcontroller on an electronic board to read from and write to an S25FL064 flash memory chip. I'm currently using the nRF5 SDK . Before I could read...
I am trying out the Nordic Bluetooth ESL sample example code from the link [ Getting started with bluetooth-esl-and-periodic-advertising-with-responses-pawr ]
Downloaded...
I understand from many posts that the DTS file is ignored when in multi-image (mcuboot enabled) I need to change the partitions to reduce the bootloader from 48K to 32K &...
Hello Nordic Support Team,
I’m currently experiencing issues connecting to my nRF52833 hardware. The device was previously working without problems, but now I’m unable to...
Hello, I am currently developing with NRF52840 and NRF7002 chips. I am running a custom version of the wifi scan sample, using the baremetal library and custom shim file....
