Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
We're trying out using devcontainers in WSL to develop Zephyr based software for our products. For flashing products from within the devcontainer we're connecting the corresponding...
Reference link: https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-9-bootloaders-and-dfu-fota/topic/exercise-1-dfu-over-uart/ I have an nRF54L15...
Hello everyone,
I'm working on a design using an nRF SoC and have a question about the correct way to handle I2C pull-up resistors in a mixed-voltage system.
My Setup...
Dear Nordic Support Team,
I’m encountering an issue during debugging where the code consistently hangs at line 360 in nrf_sdm.h , specifically at the following call:
...
Hi,
We are working with nRF52832. Over requirement is we need to transfer the file over BLE. We are using UART service (nus) to transfer file over BLE we getting maximum...
Hello,
I am working with a thingy9160 to connect to an MQTT broker using TLS.
I have run into an issue where the MQTT connection is disconnected with error code #XMQTTEVT...
Hi,
I have a nrf52833 with MCUBoot and BLE, I am using NCS v3.0.1.
I need also a custom NVS partition to store user data, so i create a data_partition for this purpose...
Hello,
I'm trying to build a Zephyr module that manages some features for a specific board (an SDK for that board). In it, I would like to enable the IPC devices in the...
I am testing data transfer from a microcontroller to a host PC using USB CDC ACM on the nRF5340. Right after powering on the microcontroller, only the first packet takes longer...
hi support team,
do we have any samples on how to show radio statues to gpio? when radio is on, gpio is set to high, and radio is off, gpio is set to low.
waht i can think...
Hi everyone,
I'm in the middle of a project and am starting to run out of available GPIOs.
To save a pin, I was wondering if it's possible to use a single GPIO (for example...
As a detour to getting DFU working for my existing project, based on nRF54L15, it was suggested in a previous ticket that the issue might be with my custom board folder, and...
Hello,
I would like to ask if it is possible to print the status of individual parts of memory on nRF7002-DK while the program is running? So far, I have managed to print...
I am using ncs to develop for NRF54L15. It runs fine on the development kit DK, but it doesn't work properly on my own hardware board. My program always fails to simulate...
