Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
Dear Nordic team,
i am stilll struggeling with the GPIO set-up in system off mode. It seems, that both GPIO_INT_EDGE_TO_ACTIVE and GPIO_INT_LEVEL_ACTIVE are working fine...
I am getting started with the nrf52840 dk, and I am unable to clear the flash with the Quick start . Here are my logs: 2025-09-24T02:11:29.285Z INFO Initialising the bundled...
Hello,
I'm trying to connect an SPI device on the nRF54L15-DK kit. The Nordic support page says it needs to be configured using the board configurator , as seen in the screenshot...
Hello,
I would like to ask if it is possible to upload a program to nrf7002_DK where it will be possible to select Wi-Fi STA or AP mode? I tried to connect it, but the compilation...
So I have a timer interrupt setup which triggers every 1ms in the interrupt I give the semaphore with The interrupt triggers correctly as seen from logic analyzer this should...
Hi,
I’m working with the Matter Door Lock sample in NCS 3.0.2. With the default PRODUCT_ID = 0x8006 , everything works as expected: commissioning to Apple Home and Google...
Getting a Precise data bus error - BUS FAULT, when sending a http POST request to an https sever over tls. Cannot decipher the exact instruction address as on enabling CONFIG_DEBUG_OPTIMIZATIONS...
Hi, I have a device using nRF5340+nRF7002. I am storing multiple wifi credentials and using auto connect. I have some questions: 1. Using auto-connect, how does the SDK/wifi...
through RTC i am trying it but it is not happening can you give any propre example one for the sleep mode enabling and wakening up from the sleep mode.
Hi,
I'm using the peripheral_hids_mouse example from NCS v3.0.2. What's the correct way from SC(Secure Connections) to enable Just Works pairing ?
Thanks!
The nPM1304 requires the CC1 and CC2 pins to be connected to the USBC port. Can they be left open/grounded on the IC side?
The problem which arose is that CC1 and CC2 are...
Hi, I'm looking for clarification whether the DECT NR+ modem firmware supports GNSS. Legacy docs say it doesn't, but there is no mention of it in current docs. Based on that...
Hi,
Issue
With the official nRF21540-EK + nRF54L15DK setup, my app/config works: advertising, connections, and PA/LNA behavior are all OK.
On my custom PCB ...
I am attempting to do channel sounding with one initiator and two reflectors. Switching between reflectors, by connecting to each in turn, does work, but it is very slow....
