The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hello,
I am creating my own board with a nRF5340. I see a development board with a PCB antenna. I do not have the thousands of dollars for the simulation software. What...
C:\nRF5_SDK_17.1.0_ddde560\nRF5_SDK_17.1.0_ddde560\examples\peripheral\spis\pca10056\blank\ses project is giving me the errors listed bellow when trying to run the example...
Dear Team,
I have nRF54L15-DK and my firmware is running fine over there.
Now I want to use nRF54L15-DK to program & debug standalone NRF54L15 on a my custom board....
Our existing product (already in the market) at Element Science in San Francisco, CA, USA uses an nRF52832 (BMD-350 module by u-blox) and nRF5 SDK 15.3 as base for the firmware...
Hello, I have two nrf52840-dongles which I am using to test ESB. (NCS 3.1.1)
With a few modifications to the ESB prx and ptx samples:
Remove logs except for PTX ESB_EVENT_RX_RECEIVED...
I upgraded my sdk from 2.6.1 to 3.1.1 and after resolving a few issues everything was working just as it was before the upgrade except for MCUmgr. When I run the MCUmgr client...
Hi,
I recently migrated a project from NCS v2.x to NCS v3.x and noticed that the method I previously used to generate a device-unique identifier no longer works the same...
I've seen similar threads but haven't yet found an answer that works for me. I don't know much about encryption but I've been tasked with adding 256-bit AES GCM to our project...
On a BLE Peripheral NRF52840 built with nRF Connect SDK v3.0.2 , high-rate GATT notifications sometimes push the stack into a state where no (HCI 0x13) events arrive for the...
Dear Nordic support:
How long is the single broadcast duration and the broadcast interval for Bluetooth? We would like to know what the duty cycle of Bluetooth operation...
I am trying to Build a modified version of the Matter weather station with additional endpoints I have created a custom Cluster and Custom Device type via Matter Cluster editor...
Hi，nordic
My ncs verison is v3.1.0;
Can I use ANT+ and BLE protocol together in nrf54l05 ？
Does garmin have ANT for nRF Connect SDK support nrf54l15 dk now?
If I...
Hello,
I am looking for ways to measure current during the transmit and receive test for the 2NR modules.
Can you please provide me the steps to do that?
Also what application...
Greetings, I'm developing a custom hardware using nrf9151, i've tested the gpio and serial interfaces of the custom module and the work fine, when i try to flash the serial...
