Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Hello Nordic Support Team,
I am currently working with Bluetooth LE Audio using the nRF Connect SDK and Nordic hardware (e.g., nRF5340 platform). I would like to better...
Hardware :
n RF5340 on F ans tel B T4 0F module
Custom board , not a D K
High voltage mode : V DDH supply 5V , VRE GH V OUT set to 3.3V
DC /DC mode ...
Good day, everyone!
So I've been trying to implement a USB HID device in my development board for a few weeks now with the aid of some chat bots but it's gotten to a point...
In the cs_de.c, we have an IQ pair extracted from remote_pct and local_pct. Assuming this code runs on initiator (where the ranging is done), and remote/local stands for reflector...
I tried to use NRF_SOCK_RAW and NRF_IPPROTO_RAW to create socket, but found `modem fault`!
//this is my wrapper
socket_create ( true , AF_INET , SOCK_RAW , IPPROTO_RAW...
Hi, I very much doubt this is a SoftDevice issue but sticking it out there as an Apple dev asked me. Short story is I have users in production using an App connecting to NRF52810...
Hello Nordic Team,
I am using nRF5340 DK as a debugger/programmer to develop firmware for the Fanstel EV-WT02C40C module. My goal is to do i2c communication between Renesas...
Good morning, I have built and flashed the l2-e1 exercise on both the nRF5340DK and the nRF54L15DK. When the nRF54L15DK boots, the following output is displayed in the terminal...
Hi,
I’m working on nRF54LM20A and trying to configure the internal capacitors for the 32.768 kHz crystal (LFXO) using the factory trim values in FICR.
According to the...
Hello, read through the documentation about the SAADC and found the TRIM.LINCALCOEFF[n] register. ADC-linearity is important in the project I'm involved in... Seems that the...
Using nrf connect SDK 2.5.0
The nrf device is an L2CAP CoC server. I am using an RPi 4 to test with. The application is for transferring data through UART to another chip...
Greetings!
We have been using an nRF52840 Development Kit for a while now and have been performing FW updates OTA (between the same 3 FW images, cycling and updating between...
I am still on the learning curve of nRF Cloud (and the nRF9151 in general) and am trying to add A-GPS to a project.
Using nRF Connect SDK and Toolchain 3.1.1, I cannot add...
