Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi..
i am using nrf52 and my custom made android application.
softdevice is 132.
in that am able to do DFU for application file with android master control panel.
i used...
Hi.
I will make clock.
I use RTC2 + Softdevice. (PCA10040 , NRF52832 , s132_nrf52_2.0.0_softdevice.hex )
Base Source code = nRF5_SDK_11.0.0_89a8197\examples\ble_peripheral...
It seems to me that Nordic has implemented only a part of the Current Time Service.
I want to get the time zone in addition to the year, month, day, hour, minute, second...
Hi.
I'm developing firmware based on github.com/.../S130_LBS_client_server_central_peripheral example. I installed third party Softdevice s130, and with example of peripheral...
I have modifed the nus_uart(peripheral) to add static pass key in sdk 10.I used my mobile phone to test the functionality and it works as expected[asks for the passkey when...
Hi,
I'd like to put a BLE central in low power between two scan.
actually I use the example Ble_app_uart on a dk board PCA10028
and a second dk board as advertiser with...
Hi,
I am trying to get the SPI Slave working but was hoping to find a how-to. Is there an example of the SPI Slave for the S110 Soft Device (7.3.0)?
Currently, I am...
Hello,
I am developing custom HAL driver for SPI in NRF52 (PCA10040). The problem is that using the EasyDMA MAXCNT registers value must be between 1...255. It implicates...
Hi,
I am using nrf_pwm_noglitch.c from here . Is there a way to stop the pwm cleanly?. I would like to have a nrf_pwm_deinit(); similar to nrf_pwm_init(). Currently I set...
Hi.
I'm using PCA10028, SDK10.0.0, S130.
About "ble_app_multilink_central" for the reference.
This code shows me below sequence.
Scan->connect request->get connection...
Hi,
We have an application where we have very very slow vcc risetime and therefore we have an external watchdog reset circuit connected to the -reset/swdio pin in order...
Hello,
the available QDID for nRF52x refers to Softdevice which has no IoT capability, being this a work in progress.
When this will be ready, will Nordic release a new...
Hi,
I want to use the NRF51822 without the Bluetooth functionality. Is it possible to leave the pins ANT1, ANT2 and VDD_PA unconnected? If no, what is the cheapest way...
