Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
Hi,
Im trying to use the NRF51DK evaluation board as a data channel between another MCU
and the PCA_10031 bluetooth dongle. Im not using softdevice.
My implementation...
A week ago, I asked about this warning in the product specification:
"If the antenna is exposed to a strong NFC field, current may flow in the opposite direction on the...
I'm working on a project that requires my device to be able to identify when a phone connects that has been previously bonded and placed in the white list. I need to be able...
Hi,
I have developed two different application on nRF51822 with two different location. One is start from 0x1D000 with max size of 16 KB and another start from 0x21000...
When i am trying to transfer data over air using sd_ble_gatts_hvx() function every time i am getting err_code 12 ( NRF_ERROR_DATA_SIZE ) error.
Here i can send data from...
I'm working with ble_app_uart_s130.
Compilation is fine and it works as expected in hardware.
I'm going to add application timer and scheduler.
To do that I have to set...
I want to use ADC / PWM / I2S / UART / SPI / I2C / at a time.
So, Can I use all GPIO pin assign any function?
If I can't use some function at a time, I want to know the...
Launch an example for UART (BLE PERIPHERAL) on the board PCA10040. When try to set the parameter APP_ADV_TIMEOUT_IN_SECONDS = 0 (no timeout) get returned NRF_ERROR_INVALID_PARAM...
Hello,
I have a question regarding AVDD pin.
I am using nRF51822 CEAA package. And the reference circuitry on the datasheet uses a 1.0nF capacitor between VDD and GND...
Hi everyone
I'm facing a weird problem in my design and FreeRTOS. Apparently, my system was working fine, but along I'm adding more tasks, i've detected the system stops...
I'm using RS485 driver on NRF51822 uart. I started software developing with ble_uart exapmle.
RS485 as always has direction control inputs.
Before data transfer to uart...
In my app I have the following:
s110
20 ms min connection interval
100 ms max connection interval
4000 ms con_sup_timeout
I'd like to set the slave_latency...
Hi,
The documentation states -96dBm rx sensitivity for 1mbit BLE mode and -93dBm for proprietary 1mbit mode.
Is it possible to use BLE mode (3 in MODE register) but...
I want to scan for peripheral devices in central-role and at the same time i want to broadcast in peripheral-role. How do i have to initialize the Softdevice in this case...
Hi,
I'm originally iOS app developer.
I have been developing with custom PCB that based on nRF51 chip. (not nordic development kit)
My PCB has a gyro sensor and some...
