Hello,
I recently got a BL653 Click Board and am trying to program it. As I do not have a supported MCU for the NECTO Studio IDE (the ClickBoard's manufacturer IDE), I...
I was looking down at the pinout schematic of the nrf52840 aQFN73, in the schematic provided in the data sheet from v1.1 to v1.11 VSS_PA pin is below ANT pin, but once in...
Hi,
I'm looking to use the nrf connect sdk for development that is compatible with the latest zephyr lts. I believe it will be ncs 2.9.2 compatible with zephyr 3.7.99 (3...
I'm still new to this but particularly in regards to battery. I have a custom board with a nrf5340 and have been working on reading the voltage. I used the battery sample...
This is NOT a runtime error it's a compile time error (application). Failing at stage [154/159] Linking C executable zephyr\zephyr_pre0.elf
Having started by following...
Hello,
I am designing a custom PCBA based on the nRF7002DK PCBA and I really need the Fabrication Notes / Drawing that officially went to the fabricator to direct the build...
Hi,
I purchased nRF52 DK 2 PCs. PCB labeled
PCA10040
3.0.4
2024.34
boath board are new and box packed. from first time itself. I am not able to flash the board...
Recently we are purchased nRf51dk and nRfbeacon boards for FOTA function but both boards are not working, we already followed the follwoing links:
1. developer.mbed.org...
Hi nordic engineers,
I want to add a mouse function in the keyboard application project, but have some questions to know:
1.Does BLE support such compositive device...
Hi,
I am new to the BLE and Soft device stack, I am working on Multi link peripheral example with SDK version 9.0. I have flashed the S110_nRF51_8.0.0 into the nRF51-DK...
I wanna to make an iBeacon device based on ble_app_beacon example.
I found in the example the default advertising mode is BLE_GAP_ADV_TYPE_ADV_NONCONN_IND, where its advertising...
Hi all,
I just received my nRF52 DK and started attempting to run examples on it. I am having an odd trouble that the LED2 is always lit after programming the board, no...
Hello,
I ran PCA10005 board with nrf51-ble-app-lbs application and programmed PCA10004 with S120 ble_app_multilink_central. I have connection between them (I just changed...
Hello everybody,
I am currently experimenting with BLE on the nRF51-Ek. At measurement on the oscilloscope, the BLE protocol shows a behavior that I do not quite understand...
Hello.
I get error 0x10 (error for invalid flags) when i want to write to peripheral with my master module. I use the same code i always used, and i didnt change anything...
Hello.
I written code for nRF51822 w/ MPU6050 in S110(8.0.0) and Keil.
I tried to setup gyro as bellow.
twi_master_init(); => mpu6050_init(MOTION_SENSOR_ADDRESS);...
Hello
I have connected the nrF51-DK board and it was recognized by the computer.
I have managed to put in in a boot loader mode.
Since I switched it to boot loader...
I have three pca10001 boards. One is programmed as multilink central and other is programmed as multilink peripheral. when both peripherals are connected to central, the central...
I'm a newbie for Nordic development.
I just noticed that softdevice, app, and bootloader share the same CPU, RAM and Flash at the same time. This three software modules...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
Hi
I use an avr attiny441 with the nRF24AP2. Communication is over SPI byte flow. After start up, I get the start-up-message from nRF24AP2. That's fine. Afterwards, when...
