Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
I have a new nRF52 Preview Development Kit, after connect it to a computer with a USB cable, the status light (LD5) come on, indicating it has power. However, the standard...
I am working on a project to integrate nRF51822 with a rechargeable battery,
and make it chargeable through micro USB cable.
Any recommendation on the battery model, charger...
I have a dual mode BLE / ANT+ nRF51422 design going through regulatory testing for FCC / EU marketing approval. I have previously successfully tested a very similar design...
The spec of nrf52 mentiones 'Propriatary RF' as option. I was wondering if that could be used to implement 802.15.4 which would save us an entire IC and power and like basically...
Hi there!
I would like to implement the nRF24L01-module to one project.
But, it would be great, too, if i can use the application manual to use only the chip itself with...
I have the nRF51-DK development kit (PCA 10028). I'm following the gcc tutorial here - devzone.nordicsemi.com/.../.
I'm using the ble_apps_hrs project as a basis for my...
Is it possible to connect DCC / DEC4 to a transistor to turn on / off a part in my circuit? I assume yes, but I just want to make sure.
Or, is there another way to turn...
Hi again,
If I use BluetoothGATTSetCharacteristicValue and set wr_auth = 1 in the ble characteristics, I receive a BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST event. I can also see...
Dear Nordic developers,
Does TWI supports bit level clock stretching? Means that after each bit (not byte) slave can hold down the clock and master should perform appropriate...
So I have the following bootloader code:
int main() {
uint32_t code;
sd_mbr_command_t mbr_command = { SD_MBR_COMMAND_INIT_SD, };
code = sd_mbr_command(&mbr_command...
My ANT BLE application runs on a custom board with a nRF51422, SD 310 rev 2.0.0
I can use the nRF UART app on an android phone, but on an iPhone with iOS 8.4 I can't even...
Hello,
I'm using an PTR5188 development board for my project which breaks out PIN 26 & 27 for ADC only. I'm using mbed as my development platform and haven't been able to...
Hi there
Can you clarify a point for me?
Quoting from Gazell link layer user guide:
"If only the ACK packet sent from the Host to the Device is lost, but both the initial...
Hello.
Reading the documentation of pstorage_load and the actual implementation has left me with confusion.
The documentation states that the size and offset parameters...
