I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
When starting nRFgo studio it crashes instantly. I have tried uninstalling it several times. It appears to install correctly including all the J-xxx components, but will not...
Hi,
I have a device in the central role that connects to a device with a specific name. I then do a db_discovery_start to get the handles of two of the characteristics...
Hello,
I'm trying DFU/bootloader.
Using nus service
Switch to dfu when necessary
At this time, watchdog (2 Sec) enable state does not execute the bootloader...
Hi,
I am mobile developer and very new to mcu programming. Due to our new product's requirements, I have to write program with new bluetooth chip. So if nrf51 and nrf52 series...
To find a clean channel for 2.4g Band to avoid the wifi channel, nRF24L01p would sweep frequency for all the channel (2400M~2525M). But looks like nRF24L01p not support to...
Hello guys!
I'm trying to port the TSS service to one of my projects.
This project is based on SDK13.1 while the Thingy is on SDK12.1
I have a lot of problems with...
Hello guys!
I'm trying to get softblinking led work with a SDK14.
The code works perfectly fine in one of my projects that use scheduler and SDK13.
But in SDK14, (only...
Hi, I think the idea of limiting the behavior of a model to states is very wise, but due to my limited understanding in this matter, I find it puzzling as to what happens...
Is it possible to use the NRF52832 UART in half-duplex single-wire mode, by assigning TXD and RXD to the same GPIO, setting the GPIO drive to disconnect '1' and using a pull...
I am running the example under peripheral\pwm_driver on PCA10040, and SDK 12.2.0. Using a scope, I measured the period (from rising edge to rising edge) on one of the LEDs...
In my project, the softdevice I used was S110
I hope that some of the data can still be retained after OTA updates,
in the Bootloader program code:
#define DFU_APP_DATA_RESERVED...
Hey togehter,
has anyone succeeded setting up a connection between ST-Link and nRF52832?
I connected the pins (GND, SWDIO, SWCLK and second try with GND, SWDIO, SWCLK...
Hi,
Please let me what is the beacon layout of nRF58122 for scanning beacons in region by using following method:
BeaconManager.getBeaconParsers().add(new BeaconParser...
I'm using and NRF52 with S132 and SDK13.0. I'm using Keil as my IDE.
My application acts as a central for smart phones to connect to and also acts as a peripheral to conect...
