Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
It is possible to run easily a SoftDevice stack (e.g. S110) on nRF51422 using an accurate 16MHz external clock reference for HFCLK instead of an external 16 MHz crystal oscillator...
I want to change data bytes in the advertisement packet. In ACI_DEVICE_STANDBY I put: lib_aci_open_adv_pipe(1);
In ACI_EVT_CMD_RSP: I get feedback that command 1B (I assume...
first,PCA10005 can't load sofeware hex that after s110 7.0.0 hex(include 7.0.0),and gostudio note that the given hex file can not open successfully.
second,the PCA10005...
hello ,
i am trying to make communication between two (stm8s+nrf24l01) modules for which i am using this link zewaren.net/.../110 ,
by this code i am able to transmit data...
hello,
i am using ble_uart_app project in that i have added the pwm feature and added my code. i have tested my code seperately it works fine but when i have added in the...
Hello,
I'm realizing dfu.
1st case - for test
NRF_LOG_PRINTF("main start\r\n");
// ******* main loop start ******* //
while (1)
{
enterBootloader();
}...
I'm trying to set a global variable in RAM as uninitialised so it can be read back after a soft reset condition:
uint32_t data __attribute__((section("NoInit"), zero_init...
Developing an application on nRF52 DK board using Eclipse Neon.3 (4.6.3). When the program is run the following message is displayed in red across the bottom:
There are no...
The micro ecc works well in sdk11.0. However, after I recompile micro ecc in sd12.2, micro ecc can't work in S132 3.0.
I append micro Ecc functions to the Uart Demo in...
I am having a strange issue with the serial DFU in SDK 11, s132v2, specifically running either dfu_dual_bank_serial or dfu_single_bank_serial. My goal is to simply get the...
Hi,
I'm trying to use the GPREGRET register to save some state across resets. It seems to work as documented, but I'm getting the following error after each write operation...
Hello all,
I am working on nrf52DK BLE_UART_APP and i would like to know where the recieved data?(sent from the smartphone app / terminal) will be stored in the controller...
hi all,
I have this problem:
After enable the indication i send for indication , with a snuffer ble i recieve them. But the master control panel lost the first?
...
i want to connect the bluetooth of device (nrf51822) to my android phones bluetooth without using master control pannel.i want general bluetooth connection. can you please...
Hi,
I'm using nRF5_SDK_13.0.0_04a0bfd on nRF52840.Basing on the ble_app_multilink_central example, I want to write some data to flash to save. So I use the fstorage. After...
Hello,
in SDK 11 I was using non blocking function to check if there is data to read from UART logger called: NRF_LOG_HAS_INPUT .
I can not find any function like that...
S140, nrf52840, as long as I call sd_radio_request before calling sd_ble_gap_addr_get, the program will crash and enter a default error handler, it's not the case if the sequence...
Hello.
I notice a problem with app_uart_flush function, which is calling app_fifo_flush function and in this we have a:
uint32_t app_fifo_flush(app_fifo_t * p_fifo)...
