I want to use the Softdevice Controller without a crystal on the RTC. I configured my project with
Advertiements look fine, but interaction with a BLE central either throw...
Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
I'm using the prebuilt Aliro stack (libaliro.a, nRF52840), when a session fails inside the library we have no way to get the resulting AliroErrorCode. The stack entry points...
Hello,
I'm using nRF Connect for Android, and transmitting data from a Intel Genuino 101 board. The data I need on my phone is simply an integer, but I can't manage to show...
Using the thingy52 microphone function, some models of mobile phones receive data will be lost, under normal circumstances, 1 minute will receive about 60 packets of data...
HW: nRF52, PCA10056
SW: SDK15
I'm using the nus_c service with multiple central connections.
After change the GATT Write operations from BLE_GATT_OP_WRITE_CMD to BLE_GATT_OP_WRITE_REQ...
Migrating from 13.1 to 15.0. getting error, undefined reference to 'ble_evt_handler'
In 15.0, peer_manager.c has the function, static void ble_evt_handler(ble_evt_t const...
Hello,
I tried a migration of a bootloader from SDK 14.2 to 15 but my bootloader does an infinite loop @0x24d70.
Do someone have an idea of what can i do please ?
...
I'm working on an application in which we are using a custom board with the NRF52382, which is powered by a battery. We sample our ADC every 6ms, record these values for about...
I try dual bank DFU on nrf52832+SDK15.0.0.
After extract new image to dst_addr(run image_copy),
DFU run nrf_dfu_settings_write().
nrf_dfu_settings_write() is run, nrf_dfu_flash_erase...
By setting either:
ble_gap_adv_params_t::duration
or
ble_gap_adv_params_t::max_adv_evts
to a non-zero value should trigger the BLE_GAP_EVT_ADV_SET_TERMINATED event...
We are planning to use Adafruit BLE Feather with the IAR / Keil/ SWD tool chain for a small scale project . I notice the Adafruit BLE feather memory map is quite different...
Maybe I'm wrong but this seems to be wrong ASSERT in the function:
My understanding is that max time which can be set on timer is dependent from timer frequency and timer...
Hi There, i am pretty new to this ble and arm world. i was exploring my nrf52dk with sdk15 cryptography libraries. I have looked into an example of Elliptic Curve Diffie-Hellman...
Hi,
I had done secure OTA in my custom board using SDK12.2.0 with S130 v2.0.1 softdevice. But when i am trying to update the same for multiple times then its not happened...
Hi!
I'm running UART example and modified to run upon interrupt and its working fine, but in main() if condition ( if (cr == 'q' || cr == 'Q') ) is not executing even condition...
