My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
nrfutil install fail.
I want to update with BLE secure OTA, so install the nrfutil tool. and run the command as following:
but report download pc-ble-driver-py 0...
Total noob here using SES on a Mac to build BLE peripheral (S110) firmware for an nRF51822-based device with SDK v15.
So far I've been able to get the generic portions of...
Hi,
I'm developing on nrf52810 using the SDK14.1.0 and I've take as starting point a template application that targets nRF52810 running on the nRF52 Development Kit. But...
Taking a look through the SDK, there are very few examples using the dongle. I've tried building some of the existing examples by changing the board definition in the preprocessor...
I have a porject working well with normal ble function such as ancs and other services（use sdk15.0） , when I add the mesh model light switch on_off (source code copy from...
Hi.
I applied https://github.com/crfosse/Thingy-52-to-nRF52xx project for get thingy motion data by nRF52840.
But It still found 6 Service for motion service,...
I have a use case where I need to send a sequence of 2 byte bursts as SPI master. The data is generated on the fly and the algorithm would be able to saturate the 8Mbit/s...
Hi,
I just installed nrf connect 1.1 on my Dev-PC (many versions of J-Link and nrfjprog) everything works fine. The visualization of Secure-DFU-Upload-Speed is really nice...
SDK version: nRF5_SDK_15.0.0_a53641a
Softdevice version: s132_nrf52_6.0.0_softdevice
PDK: PCA10040
I am trying to read the ADC pin value using the SAADC module, I...
Hi, I'm using external board with nRF52832. (SDK 15.0.0)
In my external board, there are no RTS,CTS pin. So I don't use hardware flow control (HWFC).
The problem is, I...
How do I add a 128-bit UUID?
I am using SDK 14 and see hardly any examples of how to put a 128-bit UUID in my advertisements.
The only relevant example I found is under...
I am trying to package a firmware update and flash it over BLE DFU and I keep getting the following error on the nRF Toolbox app:
"Upload Failed: Unknown Command"
I cannot...
So, I am using the NRF51 as a SPI slave for an RPI3B+. On a l ogic analyzer and O-Scope the Pi is sending its MOSI SPI data perfectly fine. On top of this issue the nrf_drv_spis_buffers_set...
