Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I'm interesting in knowing a little more about the "address match" output of the nRF905 chip. What is the expected jitter related to the actual radio signal?
E.g. If I...
Using softdevice s132, nRF52832 on a custom board
I don't quite understand how does the SPI work exactly?
I am using it on a battery powered low power sensor application...
Hi,
We are unable to run testing with Nordic nRF52840 preview DK boaed as it is not able to be put into DTM for RF-PHY testing.
I need the hex file to flash and the...
In the nrf52 specification:
"The Phase A, Phase B, and LED signals are mapped to physical pins according to the configuration
specified in the PSEL.A, PSEL.B, and PSEL...
Hello Everyboby,
I want to know how to configure can use Public address for advertising when using nRF connect APP? Now, I just can use Random address for advertising...
Hi,
for production purposes, we need to define the components of our circuit. Less specific definitions of the parts are prefered to ensure the interchangeability of common...
Hello is it possible to send message from nrf52840 to nfr24L01, I tried (pca10056 as transmitter), program is esb_ptx_pca10056 and nrf24L01 as receiver, but could not receive...
Hi,
I would like to create a DFU package for updating an application config flash page.
We have a device where the device reads some configurations from a specific flash...
Hi Team,
Scenario-1:
There is a use-case where 8 to 10 peripheral devices need to be connected with the HUB which is based on nRF52810 and a mobile device should be...
I'm working with nRF52840 on a battery powered device , as a result theres a constraint in the total power of the cell . Now , it's been decided to use the USB2.0 at full...
Hello,
I have a problem with communicating with SD cards ( https://devzone.nordicsemi.com/f/nordic-q-a/34401/fatfs-example-does-not-work-with-every-sd-card ). I resloved...
Occasionally, the NRF_LOG output just keep putting out random old log data. I have enabled the timestamp so I know they are old data. Once it happens, it just stuck in an...
Where do we get support for NRF24L01+ ?
There is no option in the pull down menu for the device.
I attempted to set up a profile for private support but they have made...
Hello , I am having 3 nRF52832 DK . I tried Light switch - proxy_client and proxy_server example . I provisioned nodes using nRF Mesh app . Here i want to send data from server...
Hi! I'm trying to figure out the nrf_ringbuf module, and would really appreciate some advice about its intended use case. The api exposes the following functions:
This...
