after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi, we are using SoC nrf52810 SDKv14.2-SR3v1.2 for our RCU.
1.If there is a scenario the image transfer is finished, and the power lost happens when the old image is being...
Hello,
I am in the process of determining a system architecture for a sensor-bluetooth-android application. The goal is to read sensor information from an Android device...
I'm using Mesh SDK v2.2.0.
I want to create a new custom model,but I don't understand difference between Generic and simple onoff model.
Which model should I study?
I remember reading somewhere an article on how debugging with softdevice was going to be easier, with the debugger doing something along the lines of actually not stopping...
Hi dear nordic employee:
I use blew：
chip：nrf52832 CIAA-B00
SDK: 12.3.0
what‘s I want is same as this ， when the interrupt happen，I want to know the toggle is HIGH_TO_LOW...
Hi,
I want to develop a 4 Chanel Wireless audio system
I am using an EEPROM (without MC) to configure the nRF24.
I want to split the available band (2,4GHz to 2.5 GHz...
Hi,
I have the problem, that nrf_crypto_init() does not find any backends and thus is skipping the initialization.
What is the precondition for NRF_CRYPTO_BACKEND_SECTION_ITEM_COUNT...
Hello,
after migrating to SDK15 we noticed, that our spi master seems to clock out single bytes instead of a continous clock for the whole transfer.
The Migration guide...
Hi
I want to update bootloader.zip file over BLE DFU mode without signature checking , the open bootloader example only for USB,
How to disable bootloader signature checking...
when message relay by any node how can other node know that it is for him and update status.
for example if I subscribe some nodes to 0xc001 group and others to 0xc002 group...
Hello,
I am making a PCB for my project using the nRF51822 chip? Can I power a LED with the GPIO pin or do I need to connect a MOSFET to drive the current? Also, I want...
Hello everyone, the sdk version that I use is 15.0. The soft device is s132.
With the example of peripheral/uart I am able to receive the serial uart sensor data. On the...
hi,
I'm trying to merge the the proxy server and beaconing example together. When I compare two main.c and copy the advertising part from beaconing to proxy server example...
Hello everyone, the sdk version that I use is 15.0. The soft device is s132.
With the example of peripheral/uart I am able to receive the serial uart sensor data. On the...
