Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hello
I am running gls example on SDK14.2.
I paired after flashing program to my DK board, and then turn off power.
And turned on again, but i can't connect to my DK...
HI. I used a translator.
I am using the RNG example of SKD15.
I know that when I set the range of the random number to 1 byte, the number from 0 to 255 is generated. ...
I am using a Raspberry PI as a 6LoWPAN router, running Raspbian 9.4. Linux 4.14.34. Radvd 2.15.
I configured everything as described in IoT User Guide . I am using Miredo...
Hi,
As well know, the nrf51822 can only work either TX or RX mode at the same time.
Normally, the nrf51822 device is working in RX mode (by using function "nrf_esb_start_rx...
Hello, i'm trying to updade my firmaware using the DFU. I manage to do it with nRF Connect and nrfutil but i'm trying to a custom central to flash the software without any...
Dear all,
I am using an adafruit-nrf52-pro-feather (nrf52832) to run my project of detecting voice by this below scenario:
++ Setting up:
[PC] ==== USB cable ====...
To learn how to use FDS, I started by importing the code from the flash_fds example. My application is using peer manager and I got really strange errors until I realized...
Hello!
I am trying to set up the interface between an ARM Cortex-M4 andthe nRF8001. After RESET I see following data on the MISO line:
(turquoise=REQN/CS - pink=MOSI ...
Hi,
I would like to control the LEDs based on the PTM 215B switch by programming it using nRF52 DK. Where each button in the switch should turn one LED.
I am using...
Hi, Nordic.
I'm developing multiple peripheral and a central. Central is only scanning and Peripherals are only advertising.
I got Adv data and Scan rsp data successfully...
Hi,
I work on a ANT proximity search project using SDK12.2.0 and softdevice S332v2.0.1 on nRF52832.
I have a ANT sensor which is 5cm apart from the Nordic 52832. And the...
Hi there,
Can you please tell if with 'Sniffer' I can track down and see all images shared with my pc's webcam?
If so, how can i do that?
Thank you so much for your...
Hi all,
I am moving from Keil into SES, and one of the things I am not being able to find is how to do the __PACKED pragma.
I see in SES that:
#elif defined ( __GNUC__...
I'm trying to use the SEGGER debugger with one of the OpenThread examples for the nRF52840. When I click on the "Go" button, it asks for the location of the source files for...
I think I found a bug in ble_dfu_bonded.c.
In ble_dfu_buttonless_bootloader_start_prepare() there is a call to gscm_local_database_has_changed(). The problem is that this...
