Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I have ASUS ZenPad 10 with Android 5.0.2,
BLE device on nRF51, S110 SDK9 with fixed passkey and encrypted characteristics with following settings
#define SEC_PARAM_BOND...
Looking for someone that has previous experience building multi protocol / time slot topologies using a mix of BLE (central+peripheral) & custom Gazell connections running...
Hi.
I have nRF51422 borad and want to flash to nRF51422 with JLink.
I supplied to 3.3V power to board and is connedted SWDIO to p23, SWDCLK to p24. JLink is connected...
IUsing the Master Control Panel application on my Android device to connect to my nRF51822 module (acting as the GATT server), I have implemented the Device Manager (v10 SDK...
Hello, I'm using SDK 15 and softdevice 6.0.
I use the micro as a master and I connected an i2c sensor as slave. I had put external 10 Kohm pull-ups, but I had a low level...
Hello ,
I am using SDK for mesh, I have saved .hex image file in flash.
Is there any example or any suggestion how can I run bootloader which will read data from flash...
HI:
Always error while porting,Error: L6218E: Undefined symbol app_uart_init (referred from main.o).
I added a path, and ENABLE UART_ENABLE 1 in sdk_cofig.h
Compile...
I have set up the gcc toolchain on Mac OSX to compile my BLE nRF51822 code and I tried to flash the code. Here are the 3 scenarios that I have tried (JlinkExe on Mac)
Case...
Hi,
I am not sure if this is the right place to open up a thread about a zephyr HCI firmware issue. Since Nordic also contributes to zephyr I'm putting up this question...
Dear All,
We have designed our custom board based on nRF52810 chipset. wehave not used 32.768khz oscilator. it seems in code default configauration is with crystal. so please...
Hi All:
When I simulated PWM by GPIO, the output current noise was shown like the picture below (red circle area):
Cause it will lead to a loading issue in the backend...
I want to implement a long write. The environment in use is below. · SDK15 · Nrf 52 · Nrf 52832_xxaa · S132_nrf52_6.0.0_softdevice.hex
My start is "nRF5_SDK_15.0.0_a53641a...
Hi Nordic team,
I have 2 nRF52840 DK boards.
I followed the steps mentioned in the below link, I am able to Transfer the DFU archive over serial with nrfutil(LED keeps...
I want to enable the Logger Module to have the high default severity of Error and then be able to enable lower level severities on an individual module for debugging. Is this...
Hardware used: 2 nRF52480 DK boards
I am running nRF5_SDK_15.0.0_a53641a\examples\ble_central_and_peripheral\experimental\ble_app_att_mtu_throughput example, I want to increase...
I read zephyr official document of nrf52810 support:
http://docs.zephyrproject.org/boards/arm/nrf52810_pca10040/doc/nrf52810_pca10040.html
It describes like this : ...
Hello,
I just got my nRF52832 DK and am following the Getting Started at the Infocenter to get familiar with it. Running Ubuntu 16.04 and all the latest Nordic tools (SDK...