I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Hello everyone, I would like to change the name of my device with sd_ble_gap_device_name_set (). But the resulted name in the nRF Connect app is always "N/A". Here's my code...
How do I change the name of the USB device? I am starting with the USB Audio Demo and, logically, it shows up in Windows as "nRF52 USB Audio Demo" but I cannot find that text...
I am a beginner to Nordic devices and to Bluetooth technology in general. I have set up a Bluetooth connection using the nRF51 Development Kit and an nRF51-Dongle. The dongle...
Hello
In our production facility I need to read and write NFC NDEF messages to a NRF52832.
Is there any recommendation for a working and easy solution with an USB NFC...
Hi all,
I try to create a new project to update my firmware using twi(I2C) interface.
In my test case, first i download firmware to region2 via keil, then copy the firmware...
Hi Nordic developers,
For my internship I’m developing a BLE application on de NINA-B111 module which does have the nRF52832. I'm using SDK 15.0.0 and Softdevice 132 v6...
We're disabling pending FPU exceptions and clearing pending FPU IRQs before calling sd_app_evt_wait(), as per a few references:
https://infocenter.nordicsemi.com/index.jsp...
Dear NordicSemi engineer:
I want to connect to a peripheral device using a modified ble_app_uart_c.The information of the peripheral device is below:
How can I connect...
I need to allow BLE connections for a period of time after restart, then prevent connections (unless a button is pressed). Is this functionality as simple as re-configuring...
Hello,
I am currently developing software that scanning ble advertisement packets without pairing and advertise them like beacon. I used examples which are ble_app_hrs_c...
Hi!
I'm working on HID mouse example on SDK 13.0.0, SoftDevice S1332 v4.0.5. I'm supposed to use this as a low power media button control, using a nRF52 DK. I've done a...
Hello,
We wish to use nRF52832 IC in our design. We will design an equipment which can connect to another device via BLE and can send some measurement data. Our equipment...
Hey everyone,
I'm working with nRF52810 . I want to write into UCIRs before program execution starts.
I tried to configure NVMC(Non Volatile Memory Controller) and then...
I am using the nrf905 in a project. The datasheet suggests crystals of 4mhz, 8mhz, 12mhz, 16mhz and 20mhz are all acceptable. Does the choice of crystal oscillator frequency...
Hi there, I have an 70mm wide and 50mm high PCB with an free space of about 32x26mm on the right top corner. At the moment this area is free of any traces and polygons. The...
