I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi,
I am developing an ANT+ embedded device (nrf52832, SDK14.2) , that (among other things) acts as a BSC receiver. I have a BCS sensor that is seen in Garmin Edge as 136150...
I want to transfer data using UART to BLE by Baud Rate 19200(using nRF51822).
Transfer data speed need to achieve 2KB/sec up.
How can I do it successly?
Thank you...
I noticed that you have a branch called feature/v6-upgrade for pc-ble-driver. Is that branch usable for 52840 and s140?
By usable, I mean it can be mostly usable and we...
Hello,
I am following the PPK Get started get started of the PPK board.
I am developing on the NRF52-DK (Rev 1.1.0 2017.23) - nrf52832 My SDK is the nRF5_SDK_15.0.0_a53641a...
Hello everybody,
I am using sdk14.2, s132 with Nrf52832. I want to define the pin of the NRF52 as the input and decode the incoming pwm signal. For example, I have a signal...
Hello,
I am working with the BL652 EVK from LAIRD. The EVK has nRF52832 IC inside of the module. I downloaded the " nRF5_SDK_15.0.0_a53641a" and trying to use "ble_app_uart_pca10040_s132...
Hi. I am trying to develop an multiprotocol test example using SDK 15 and nRF-IEEE-802.15.4-radio-driver on NRF52840 dk board. I need that BLE and 802.15.4 stuff can work...
I have a confusion about mac address of nrf51822, I run example ble_app_uart .
When I use nRF Connect on Android, I can see the mac address of nRF51822 is CB:16:04:4A:10...
Hi,
I use nrf52832QFAA, SDK 11.0.0, Softdevice 132 v2.0.0. I need to add a device_manager_central to my project (in my project it's easier and faster than adding a peer_manager...
Hello,
In the documentation for nrf_serial_write function (SDK 14.0.0) it is written:
timeout_ms Operation timeout, in milliseconds. Pass 0 to operate in non blocking...
Hello friends,
I am trying to flash a nrf51 dk with keil5. When I try to flash it with a multilink universal I get this error:
My settings are the following:
...
Hello everybody !
My code is based on the code of the "ble_app_multilink_central" on which, I added some of the code "ble_app_uart_c" for the initialization and the event...
Hello friends,
I am trying to use the standard uart example of the SDK 11 with the nrf51 dk and trying to update the device's name via UART. I want to save somehow the new...
Greetings,
I can get the ble uart example to work on my PCA10056 using the example hex file, but when compiling the project on the SDK 15.0 S140 it doesn't work. Specifically...
