Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
I have a local ipv4 network with a Mac laptop. There is a Raspberry Pi Thread border router connected to the network. There is an nRF52840 running the Thread CLI example....
Hello ! I have an issue that is making me crazy so far
I am trying to connect to NRF52832 devices with my smartphone. They have to collect data from sensors inside smart...
Greetings,
I'm getting some trouble trying to fix a warning. I'm running the exemple ble_app_uart_c from the folder ble_central. When I run it, I keep getting the warning...
Hi,
From the pwm driver, there is a function that use sequence that control the dimming while not blocking other task in the program, may i ask if there are any function...
Hi,
is it possible to use the GPIOTE in OpenDrain mode?
I want to use the Timer with an GPIO. So i use GPIOTE with PPI connected to the Timer. This works. But my Pin Configuration...
Dear Nordic Team,
I am trying to use the MWU to safeguard RAM of my application. Since softdevice also use this unit, I wanted to understand that where I can write the...
Hi!
I can able to read values from BMP180 but I am getting random values.It shows temperature values in some 200 range like that.How to get proper temperature value??? ...
board: custom board nrf52840
IDE: keil5
SoftDevices: s140 V6.0.0
SDK: 15.0.0
hi, I want to decrease my consumption of my board.
Now, i enable the SoftDevices and...
When I am using peripheral/cli example and debugging through RRT, I see following outcome when I am typing commands.
OUTPUT :
Command Line Interface example started...
Hi,
I am working on light switch example. I am broadcasting a message from client to servers using the API access_model_publish() with the opcode SIMPLE_ON_OFF_OPCODE_SET_UNRELIABLE...
Hi:
When I tested the DFU function of BLE, the upgrade was unsuccessful, and the APP print log prompt appeared to be a CRC check error.
The SDK version I am using is nRF5_SDK_15...
I reference demo1 of PWM driver example in SDK15.2.0, I make myself PWM driver. the official demo1 use pin17-20 as PWM channal1-channel4, but I use Pin9-P12, I modify the...
Hello,
I would like to measure the frequency of a signal and I use PPI, a timer and input capture to achieve this. Here's the configuration :
The frequency of my signal...
Good evening,
I am using NRF52840 board with softdevice S140 and SDK version NRF5_15.2. I am currently trying to compile the ble_app_hrs_rscs_relay example on SEGGER studio...
