NCS currently has a nice feature where the firmware versions are printed in the boot banner:
Is there a config option to also enable printing the nRF91 modem firmware...
Dear all,
after cutting the SB bridge to the QSPI chip and close the ones to get the pin free and disabled also qspi inside the nRF52840dk_nrf52840.overlay file I'm unable...
Hey, I have a problem understanding BLE behavior
I had a product was running in BLE phy 1M, and I wanted to convert it into PHY CODED.
It just sniffs all the advertisement...
Dear all,
I stubled upon the following issue when developing a BLE sensor product. When I try to bt_gatt_notify(); With only one characteristic, there is not an issue...
I was looking into the sdk provided by nordic for nrd52840Dk board and want to test the zigbee protocol. I havn't find any sdk for that.
Can you share me some links and...
Hello Team,
I want to configure P2.07 as UART RX for my custom board.
But when I clear the already assigned property as led2 for this pins from the pin editor gui, I am...
Hi,
I am trying to adding a coded phy support on my device in NCS project.
once I added CONFIG_BT_CTLR_PHY_CODED =y in my config , the ROM size will add more than 7kB...
Hello,
I did a side by side comparison of the latest nrfutil v6.0.0a0 vs v5.2. It looks like v6.0.0a0 is much slower.
Looking at the log from the target device, it looks...
Hi,
I have installed Embedded Studio for ARM v4.22. However, the studio crashes when I select 'Activate Your Free License'. Reinstalling does not help, and neither a different...
Hi,
In order to read values from TH02 sensor(Address: 0x40) I first need to give a command i.e. write 0x01(for temperature) and 0x11(for RH) resp into internal CONFIG register...
What is the least expensive J-Link Model is required to program a nRF52840 on a custom commercial PCB?
I see that it is a ARM Cortex-M4 core, but I want to double-check...
Hi
Im using nRF52832-QAAB0. SDK 15.3. Softdevice is running.
With debugger connected, calling nrf_pwr_mgmt_shutdown(NRF_PWR_MGMT_SHUTDOWN_STAY_IN_SYSOFF) will assert in...
Hi everyone. Do you know any example of some over the air FW upgrade of nrf52832 chip via ESB protocol. As I understand it should be some combination of bootloader with DFU...
Hello,
We have selected nRF solution for our next product line and currently evaluating the software/SDK setup for that.
We are testing following SDKs:
nRF5_SDK_15.2...
in SDK 15.3.0, no eddystone lock event (NRF_BLE_ES_EVT_LOCK) is triggered after the unlock key was changed.
according the eddystone configuration specs:
A single byte...
I use example ble_app_uart, SoftDevice sdk 6.2.1, when receive data from bluetooth, then drive IO pin 18 to send infrared wave.
received data is Infrared raw formate, which...
Hi,
Our product uses Fanstel BM832 chip. As per https://www.bluetooth.com/develop-with-bluetooth/qualification-listing/qualification-listing-fees/ , should we opt for Innovation...
Hi
I am using TH02 for temp and RH measurement
I understand I must use TWI provided in SDK. However, I a working have c++ library(Wire.h) for I2C that I used with Arduino...
Dear All
I am right now working on BLE development with nRF52840DK. I checked a number of materials, including official specification from Bluetooth SIG, but none of them...
Hi,
I need to read a couple of external inputs - think buttons (although it's actually a sensor with relay output). It's for a prototype obviously.
I need to connect at...
Hello,
I have an application that advertise specific data. Data is long enough that I cannot fit my 128bit service UUID. I think of 3 options:
1. Use my service UUID but...
Whenever I store my data in Flash using FDS (Flash Data Storage Library) it stores a random value (but fixed) even though I am giving it a value.
I run the same thing in...
