Hello,
I am working on custom hardware that is based on the nRF7002 DK. The following parts are presently listed as either EOL or NRND in distribution. L6, L8: Taiyo Yuden...
I am trying to connect some I2C sensors to the the nrf9151dk and I cannot figure it out. Where do I physically plug the sensor into the board and what configuration setting...
Nordic #Devacademy intermediate course: Ticket for exercise 2 of lesson 2
Dear Colleagues,
I selected the #nRF9151-DK, since it was in the list of recommended boards for...
My eval setup is PPK2(source mode) -> nPM1300EV - -> nRF54L15DK. I have my load connected to BUCK2, everything else is disabled.
I'm getting higher than expected input current...
I am testing gnss without lte connectivity, which seems to work ok.
Except when I get "The modem has detected a reset loop. LTE network attach is now restricted for the...
Hi Support Team
We follow the guidance of the following link to program firmware to external SPI Flash of nRF54L15,but it failed.
https://docs.nordicsemi.com/bundle/nrfutil...
I am programming and using the monitor mode with Keil seeming ly OK with nrf52-DK dev board however when I program my custom PCB it gives me an error and says the bit cannot...
I designed a reduced size PCB that used an nRF52832 and will act as a BLE HID device.
With the original nRF52DK evaluation board I was able to use the example ble_app_hids_mouse...
Using SEGGER Embedded Studio for ARM Release 3.34a Build 2018022300.35192 Windows x64
with
GCC/BINUTILS: Built using the GNU ARM Embedded Toolchain version 6-2017-q2-update...
Hardware: PCA10040, PPK
SDK: nRF5_SDK_15.3.0_59ac345
I test hrs app and get these number in current consumption during advertising. No modification on example projects...
HI,
We are mainly using "nRFgo Studio" and "nRF Connect" application for erasing and flashing codes to our custom board and its taking place successfully for a long time...
Hi, I am interested in the nRF52811 direction finding capability. In particular, whether its feasible to develop direction findings through a single beacon to receiver configuration...
I am having issues with implementing long-press button action along with normal button press on the same button using the nrf52_sdk_thread on nrf52840.
When I implement...
When mesh_config_clear() is called with a setup containing a file strategy MESH_CONFIG_STRATEGY_ON_POWER_DOWN and an entry in that file has been changed but not yet written...
Hi
I am working on Mesh using light switch example,
1. Wants to relay the ON/OFF message to other server.
2. And send mesh message from server to all node in mesh network...
Hello,
I have program w/o using softdevice to drive an LED driver using I2C. I was able to get this to work very well with out a softdevice, however once I loaded a soft...
Based on nRF5_SDK_15.3.0_59ac345 for nRF52810 application,
a. With s112_nrf52_6.1.1_softdevice.hex and app.hex, it works normally b. Add bootloader, fds_init function will...
On custom nRF51422 hardware with S110, I eventually found that after 3 minutes the advertising timeout turns off the system.
I reproduced it by using the nRF SDK v9 project...
Hello Nordic Support!
I will ask you a question.
Soon it will be mass production from prototype development. I built with MDK-ARM and wrote code with J-LINK +...
in my circuit, it takes 17ms for VCC_NRF to go up from 0 to 1.7V and reach 3.0V, but nRESET PIN does NOT to go up to VCC_NRF.
what is the potential cause of this problem...
