When my peripheral calls sd_ble_gap_phy_update, setting rx_phys and tx_phys to BLE_GAP_PHY_AUTO, I receive the BLE_GAP_EVT_PHY_UPDATE event with a status of BLE_HCI_UNSUPPORTED_REMOTE_FEATURE...
Hi all,
I recently bought an nrf52840DK, and yesterday I tried to program an external board through the p20 connector on the DK with the SWD pins. I was able to flash the...
Certainly! Here’s a clear, natural English version of your email:
Dear Specialist,
I would like to better understand the two variables used in the SDK for calculating...
Hi, Using NCS 3.0.0 it would appear that the function sntp_simple_helper does not work with SYS_FOREVER_MS as a timeout value.
Problem: When we pass this value as a timeout...
Hi All,
I have a question and slight confusion as referring to couple of links.
Performing KMU provisioning : Here we are highlighting provisioning of private key up...
Hello
I'm trying to use LittleFS with an external SPI flash, but if the SPI flash isn't available yet at boot time, my application hangs for an uncertain amount of time...
Hi, I am currently working on UART sample codes and have 2 nrf5340 Audio DKs . One acts as peripheral and another as Central. i want to modify the central board to connect...
I am using the nRF52840 dongle (pca1009).
I have read from some digital inputs successfully, but am not able to read from P0.02.
I set it up as an input with the following...
I am new to BLE and this question may seems little unusual.
My goal is to connect two nrf52 together over BLE and when i press a button in central device , a write event...
Hi!
My goal is to sample an ADC channel with 10 kHz sampling rate and acquire 2000 samples in one samples acquistion and then return to lowest possible power state. This...
Hi,
I received a Thingy91 from a colleague who orderd it shortly after hitting the virtual stores but didn't do a lot with it. I got it on my table and started to work on...
Hello,
SDK 15.3.0
s140
nrf52840-DK
IDE: SES
I am attempting to use the LPComp + NRFX TIMER 4 to count the rising edge of a signal, the timer is being used to time...
I am currently evaluating the nrf52840 for a possible future application which is based around BLE and should also provide a HID Generic interface to perform communication...
hi..I have merged the saadc with ble_app_uart and i have added all the respective files and enabled the ppi, saadc everything . while i am running the code ,getting unknown...
Hi,
I noticed something strange while developing with the nRF9160 modem's RTC. Here's the sequence of events
Connect cellular
Get time from NTP server and initialize...
Hello nordic
I'm running iot icmp example on my nrf52832.
The border router is Rapberry 4. root@raspberrypi:/home/pi# uname -a Linux raspberrypi 4.19.71-rt24-v7l+ #2 SMP...
Hi Nordic Support,
I am not getting sensor(VL53l0X) value,i used slave device address=0x29 and register address=0x01. I am getting starting distance value=255,afterwards...
Hello ,
I am trying to send 1,000 of MPU-9250 data from NRF5832 peripheral(ble_nus_uart) to NRF52832 central(ble_app_uart_c).
And i have been searched this site and...
Hello, I'm working on a project that contains 2 small enclosures each with a sRF905 and processor that monitors temp and humidity. One of the enclosures is mounted in the...
Hi, Last week we received Nordic's Thingy:91 development kit and prototyping platform for nRF9160.
The kit also included 1x iBasis SIM card. According to iBasis, LTE-M is...
Hello,
i'm using,BMD-301(NRF52832),SDK15.3.0
////////////////////////.......Issue-1..............
When i upload "twi_master_using_nrf_twi_mngr" peripheral example...
