I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
Hardware: nRF52840, running on dev kit PCA10056
Software: SDK 15.0.0, no soft device
I'm trying to get the POF comparator working, and after struggling in our product...
I just updated my project from SDK 15.3 to 16.0. I am using the nRF52840.
I am not receiving the APP_BUTTON_RELEASE event when waking up from a button press. It used to...
I am trying to the asset tracking application on nRF9160DK and following the steps mentioned in https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started...
Hi there,
I have tried to build mqtt_simple but ı got an error says:
#error bsdlib must be run as non-secure firmware. Are you building for the correct board ?
I am...
Dear Support Engineers
I am in the process of designing the automated testing platform for a 52832 based device and would like to test to make sure the components/devices...
Hi, I am trying to test the examples provided in nRF5_SDK_16.0.0 on nRF52840 (PCA20035) thingy91 device. But unfortunately, i didn't see the support files for pca20035. For...
I am using nvs_init(), nvs_read(), nvs_write() calls to store and retrieve user data. Everytime I flash a new image I use the following commands:
# nrfjprog -e -f nRF91...
Hi!
I was wondering about the Receiver Category of the nRF52840 according to EN 300 328. The device should be classified as a category 1, 2 or 3 receiver, based on the...
Hello,
I recently bought a nRF9160 DK version 0.9.0, I did a few software experimentations on it and now I would like to restore the certificates properly.
I followed...
Hello,
I am new to cloud development and was wondering if there is any more documentation or tutorials on how to use the Device APIs for nRF Cloud in addition to the guides...
Dear Team,
why is that the command " AT+CCLK" returns time with 2hours of difference? How should one compensate?
AT+CCLK? +CCLK: "19/07/19,19:57:30+08" OK AT+CCLK? ...
Using a multimeter and a Thingy:91 I've measured the current to
The nrf9160 ( infocenter.nordicsemi.com/index.jsp
The nrf52840
The total (measured between battery...
Hi,
The following article describes how to perform serial programming of nRF9160 on Thingy91: https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started...
I connected to nrfcloud using a SIM card from iBasis and the asset tracker example.
Is it possible to connect to nrfcloud using a SIM card from another vendor? (in my case...
We are trying to get the ble_app_uart project to run on an nRF52811 using Soft Device 113, since our application will require the LE Data Packet Length Extension. We started...
