Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
I would like to hide BLE advertising from normal BLE devices.
And only be able to see such advertising with dedicated scanner.
I was thinking of changing access address...
Im making a project were i have two robots each one with a device connected with a mobile phone. But at same time i want that, when they are near each other they exchange...
Hi all! I am attempting to download a file from a web server to an NRF52832 using the Nordic IoT SDK version 9.0. Are there any good reference librarie? I found a few for...
Please help to understand. How to configure nRf24L01 receiver for 4-pipe (pipe 0, pipe 1, pipe 2, pipe 3 ). But most importantly, how to specify the transmitter settings that...
I saw earlier post on this blog and viewed on-line video for LitePoint OTA tester that claims to work with all BLE chipsets. We have multiple designs with different DTM interfaces...
Hello,
I am using Bluetooth device "NRF51822_xxAC_s110". My Bluetooth is not advertising when i dump the HEX file to the Bluetooth device which is generated by the Keil Version...
Hi,
I am stuck in sending and receiving serial data over Rx and Tx in nrf51 DK. I used arduino to prototype a fingerprint access control system. Now I am shifting to nrf51...
Hi,
I would like to know if the LFCLK is enabled after zboss_start(); and after zboss_start_no_autostart().
I would like to use an rtc event to trigger a PPI routine and...
Question: for the nRF52840, if I configure a GPIO pin as an open-drain output (DRIVE setting of S0D1) and then select this pin as a UART transmit pin, does the open drain...
1 .after the flashing the board i get a Zigbee Connection and Bluetooth connection but i can't able to control the bulb by using both board and bluettoth
2. Sir i am using...
Dear all.
I know the nRF52840 has 2 uart module.
I've been used only 1 uart setting like below pin connecting in 52840 DK reference doc.
But now i have to use 2...
*** Disclaimer *** I am a total rookie on this technology *** Disclaimer***
I'm working on a small BLE proof of concept and I have an nRF52840DK board. I've got Wireshark...
Hi, guys! I'm using the nRF52 SDK 15.3 BLE_APP_UART peripheral example.
I wish to add 3 ADC channels (12-bit) to read 3 potentiometers at a sampling frequency of 6kHz. ...
Hi,
I've BLE custom data sent to nrfcloud and looking for ways to plot data. I've used "add custom card" from configuration to extract data but was not able to plot/view...
hi, I am working on nrf52832 platform and tested some Bluetooth examples of SDK_15.3.0, I want to test some Bluetooth examples like audio, media and etc, is there any project...
Hi,
I am using a BLE master to bond with nRF52832. SDK is 15.3.0. Both side support secure connection.
I have tried to set the address type of master to public or random...
Hi, I'm starting to use the nRF52840 DK, I have downloaded the segger embedded studio but I don't have idea how to start, I need a sample example to use the pins to control...
I am new to Nordic products. I have a custom nRF51822 board and I want to flash it with Keil uVision and ST-Link V/2.
As I understood, I have to program the SoftDevice firmware...
I'm implemented DFU (with custom transport, but the problem is not there). Even when flashing SD+bootloader+app+settings I can see an error in the logs:
```
14:23:48.096384...
NRF Connect sees the devices no issues and connect. When it comes to running any of the examples in the toolbox, the devices are never seen. Location services are allowed...
