I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Sdk: nRF5_SDK_15.3.0_59ac345
example: nRF5_SDK_15.3.0_59ac345.s.ble_peripheral\ble_app_hids_keyboard
question: After connecting to ios, ios virtual keyboard is automatically...
In some other non-hid app, I can set APP_ADV_TIMEOUT_IN_SECONDS to zero and it worked fine. The advertising is continuous.
But in the ble_app_hids_mouse, I set both APP_ADV_FAST_DURATION...
I would like to use AT commands to get the IMEI on a custom board that has an nRF9160.
In preparation for this I am attempting to get AT communication working on a NRF9160dk...
On the nRF52811 with the s140 softdevice, what is the set of things to do to enter very low power sleep state? The product specification says ION_RAMON_RTC is 1.5 μA. What...
Hi
there I'm having a problem in compiling an application using nrf_esb and app_timer.
./nRF5_SDK/components/properitary_rf/esb/nrf_esb.c:900: multiple definition of...
hi all, i'm trying to disable uart for lower power consumption, i've disables it with: but when i measure the voltage on the rx pin i see 1.8V (this seems to consume current...
Hi,
I'm starting with nrf52 dk using Keil ide for ANT+ applications...
I tried to run an example inside the sdk folder and I have problems with app_error functions....
I have been running a mqttsn client publisher/subscriber project (based on the example) successfully for some months. I have added a mosquitto broker to the raspberry pi border...
We are designing BLE products based on the Nordic nRF52840 chipset and star network topology which are used indoors, according to the network structure, we use one Master...
Hi everyone!
I've been using the Power Profiler Kit quite successfully for the past few months. Instead of using the UI, I designed a python app to communicate with it ...
The nRF52840 OPS 0.5.1, describes nWRITE,BLOCK as the amount of writes allowed in a block between erases, and lists nWRITE,BLOCK = 403 Maximum.
It looks like 8 blocks are...
Hi folks,
I have a system basically working with the following setup:
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(7.5, UNIT_1_25_MS) #define MAX_CONN_INTERVAL MSEC_TO_UNITS...
adv interval : 1s
adv data: 31byte
tx power: 0dBm
MCU: nRF52832
The power consumption is shown in the figure below,when I don't enable DCDC.
what may be the reason...
I followed all the steps mentioned in the tutorials. In one of the threads, it was mentioned to erase all and then try and it worked for some. I tried that as well. Still...
