hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
I'm migrating a project from SDK 14.2.0 to SDK 15.3.0, using gcc. I only just got it to link and flash. I'm using the RTT logging and the flashlog. The RTT logging is working...
I have just received a set of nRF52840 dongles and I want to write applications that run on the PC using the dongle so I have downlaoded the pre-compiled pc-ble-driver located...
Hello, I am using SDK version 15.3 and nRF5280DK.
I am having trouble finding an example that uses the button handling library .
From the information I could find on the...
I've been trying to connect my device to AWS IoT for a week, but I'm getting the same error "no matter what" I do (ERROR: mqtt_connect -45), which seemingly is an authorization...
Hi! We're developing on an nrf52840dk and have been running in to some problems when we want the system to only pull currents in the size of a few microamps. As our system...
hi, i'd like to make communicate 2 different nrf24l01+ without the enhanced shockburst if possible, i'm using arduino to control the tx and fpga to control the rx; i'd like...
Hello!
I am trying to improve the GPS-performance of our custom board. It is difficult to know if it is my hardware, firmware, antenna or something else that needs to be...
Hello, im relatively new to this and not sure why im getting this error. According to previous such error clarifications, i read that the newest versions have to be used....
Hi I have a couple of Thingy:91 devices, which we are using to evaluate the 9601 SoM.
The devices ran out of credit, but after buying more iBasis credit still would not...
Good afternoon. I use NRF 51822, and I want to use RTC 0 or RTC 1. But there are problems, if I do not initialize BLE then the compiler does not execute LFCLK_config because...
We are now developing BLE ADC sender, using nRF5_SDK_14.0.0_3bcc1f7, and two nRF528322s (sender and reciever).
We send SAADC data via BLE, after that, we disconnect, and...
I am currently using SysTick to count milliseconds in my device. This works fine, however with it enabled I can't sleep the device as it wakes up instantly.
I have tried...
Hi,
I'm not sure if I'm doing something wrong so I'm hoping someone can help me. After updating from 0.11.4 to 0.12.0 of pc-ble-python-py, I get the following error. I've...
Hi,
Please help to suggest if 10K Nodes in a single network with 100 Kbps data rate is achievable with data transmission interval being roughly every 30 seconds.
This...
