I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello expert,
I follow the steps with this tutoriel " https://rigado.zendesk.com/hc/en-us/articles/360025376053-Add-Nordic-DFU-to-a-SDK-Example ".
I reach to the DFU...
Hi
I made a custom board. (using nrRF52832)
At frist, I tested my code on 52DK(PCCA10040). It is worked.
And then I tested my code on custom board. I changed my code...
Hello,
Sorry for simple question. (Yup, I'm Canadian and we say sorry a lot!) I have SES 4.18 and nRF5 SDK 15.3.0 installed on my Mac (10.13.6) and cannot get logging (NRF_LOG_INFO...
Hi! I am using the MQTT simple sample that i have modified to continuously send data after receiving a message. I also have connected a MS5837 pressure sensor to the nRF9160...
I'm trying to get DFU OTA working with SDK 14.2.0, SD 132, on the nRF52832. I'm using the bonded implementation. My DFU event handler is getting passed
BLE_DFU_EVT_BOOTLOADER_ENTER_FAILED...
So I want to run the nRF52811 chip so I removed the nRF52832 chip from its development kit and soldered the nRF52811 chip but I cannot seem to program it. What are the required...
Hi,
I am using ncs 1.0.0 and modem fw version 1.0.1.
I am using PSM mode in my firmware.
I want to toggle state of one gpio when modem goes in active or inactive state...
Hi.
I am developing application with mpu6050 gyro on nRF52832, swd S132 V6.1.1., sdk 15.2. My code is based on ble_app_uart. In main, I add my custom function that calculates...
Hello!
I was going to start to program my Thingy 91 but since I don't have a J Link Programmer cable or a nRF9160 DK. I was planning to use mcuboot like suggest this documentation...
Hi,
I am working with MPU6050 gyro. I run the examples from GitHub for nRF52. Everything works fine, bit I have an issue with gyro output data. In register map documentation...
I'm new to Nordic, I just got an nRF 52 DK. Refreshingly simple to get working with Segger Embedded Studio on Mac. I'm particularly interested in the BLE multiperipheral application...
Hi,
I'm trying to build the asset tracker off the master branch in windows 7. I did do west update. Using gcc version 7.3.1 20180622
It fails like below. Any ideas?
...
Hello,
I have the following issue. I am developing an application very similar to the "ble app hids keyboard" example. SDK 15.0, S132 V6.0.0, nrf52832.
I would like to...
Hi!
Previous tickets 234795 and 231307 asked about the status of field updates of the nRF9160 modem firmware. Some solution is coming, but unclear when.
Are there any...
We are developing with the nRF52840, in this instance present in a Laird BL654 module carried by their DVK-BL654 dev board.
After trying three separate examples that attempt...
