Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi I wonder if there are any PPS signal from gps part to the cpu, preferable some kind of timer input or interupt port so it is possible ta make absolute timestamps with fractions...
Hi,
We are using nrf51422 in our project.So right now i am loading the program using the Usb cable .Here my doubt is can we able to flash the program by using usb to uart...
Hello. It is almost the same as the question ( devzone.nordicsemi.com/.../set-data-type-for-notify) given three days ago. I want to “Notify” new data in the “rscs” project...
does FDS have append data functions? I want to receive big files(>500KB) from BLE,but I can put it into RAM buffer, so can I create a file in FDS and append it from BLE directly...
Hello Recently I have been working on a project for a 52832+ three-axis accelerometer. I have encountered some problems. SDK15.2 IIC 1.started a timer and it was time to collect...
Hi all,
I’m currently working with the nrf9160 sip on a bare metal firmware project. I know the official support path is only with Zephyr OS but I’m facing an issue I’m...
I modified my nRF52840 dongle as is was described here Does anybody have a single diagram showing how to connect the DK's P20 pinout to the dongle ? Thanks,
Matthew
Hello! On 2019-06-24 the following mail was received:
Product update notification June 24, 2019
Hi Bojan,
We've just released a new version of our SoftDevices, version...
To the kind attention of Nordic support team,
Could you please give a very quick look at those attached gerber files? Do you think there is something that is better to correct...
Hi Nordic team support,
I want to test communication range between nRF528xx device that support LE coded with samsung galaxy s10 (support LE coded also)
1. If I configure...
For some reason I can't quite program the nRF9160 on the development board using Segger Embedded Studio (SES) when I create a new project. I must be doing something wrong...
When I set "report_incomplete_evts = 1", I get a NRF_ERROR_NOT_SUPPORTED (0x06) error.
If I comment it out, everything work as expected. I want to use it for exended advertise...
Hi All,
I need to find the RF Tx power setting of the nRF52840 by reading from the register. I understand this is possible through Jlink and the following command:
--memrd...
Hello,
I am developping a project on with the nRF9160 and I would like to have the LTE and GPS working concurently. I managed to have both working separatelly on my custom...
Hi. I am confused about flash endurance. In the product specification for the nRF52832, there is a note that flash endurance is 10000 write/erase cycles:
Does it mean...