Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
We are using regular RIGADO/U-BLOX modules (BMD300 and BMD350).
Do we need to pass PTS tests when we use Bluetooth layers (Softdevice S132_nrf52_5.1.0) with customs services...
Hello,
I'm new with ANT protocol. I read the documentation and I'm pretty comfortable with it now.
I started to develop with NRF52832 (SDK 16 and ANT stack from thisisant...
Hi there, I am a Novice in RF Board design/Antennas, particularly with nRF52 series so I have some quick questions ..
1)What are the Antenna Options for nrf52840 in mesh...
Hi,
I am using nRF52840 and nRF SDK 15.2 and nRF SDK for Mesh 3.1.
When I try to send acknowledged messages, sometimes my device needs to retry several times before the...
Hi,
I am looking for suggestions in regards to which ble example I should use. Currently, I have the hardware that writes data to a flash. I am developing the firmware...
There are several tickets from users trying to get the combination of Zephyr and Segger Embedded Studio (SES) to work on Mac OS including Catalina, but some are unresolved...
Hi,
I want to do an DFU OTA in nRF52840 BLE chip.
I have flashed mcuboot bootloader and also flashed hci_uart (To scan BLE beacons) application. This will be one time...
Hello to all,
I have a problem relating to cluster reporting: I have a device, Window Covering Device, which acts as a router and I want to connect it to Alexa, which acts...
Hello, guys.
Here they are - Thingy:91 and nRF9160-DK boards on my desk!
I was able to successfully register Thingy:91 on nRF Cloud (both SIM card + LTE modem). However...
Hello All,
I was reading about the startup code and vector table of Cortex-M4 (STm32, Tm4c123). When I tried to find out the Vector table of NRF52832 in the datasheet I...
Hi,
This is my second post about this issue, but I have not solved yet. The issue is, that I am using bpwr tx example (crank torque sensor type) with Garmin edge 520plus...
I am developing an android app which is connecting with this product. In that particular case my app advertises, the nRF scans and initiates connection with my app. Some phones...
Hi Nordics,
we would like our central nRF52840 to have DFU timeout in 20 seconds , if no connection received via nRFconnect phoneAPP to perform the firmware udpate, then...
