Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I purchased Nordic new reference platform nRF51-DK(pca10028) and try to work for DFU OTA.
In my test, first of all program S110 V7.1.0 by nRFgoStudio and downloads bootloader...
Hi
In a bit of an over-enthousiastic mood, I bought 3 pieces of the nrf51822 beacon kit, and the, as this did not gave me download access to the NRF51 SDK, bought a nRF51...
Is there an example of using sd_ble_gattc_write() to do a long write?
I'm assuming I need to use BLE_GATT_OP_PREP_WRITE_REQ and
BLE_GATT_OP_EXEC_WRITE_REQ.
devzone...
Hello everyone,
I am using the Softdevice s110_nrf51822_7.1.0_softdevice.hex and the dfu_dual_bank_ble_pca10028 example with SDK 7.1. I am trying to achieve a Device Firmware...
I am using Android Studio and am developing a system with the nRF51822. I would like to use the available sample code - nRF Master Control Panel APK for Adroid - available...
I'm wondering about the best way to implement a bonding and also a non-bonding device. There are a lot of code parts in the SDK that show a way of implementing a BLE peripherial...
I see there have been some issues with TWI in early revs of silicon, but looking at SDK 6 I see the twi_master_hw uses the silicon hardware to read/write the I2C device, but...
Hi
Can I use Bluetooth software version 7.1 en SDK versie 6.0 with the nRF51xx C0 Nordic version?
Or do we need the G0 for that?
and what are the main differences?
...
Hello
Where can I find operating characteristics of pstorage_store and pstorage_update?
Actually, I observe that about 100 ms are needed to update 4 bytes data. For...
Hi All,
I have two application modules which will use the flash , 1) Bond manager 2) configuration file
I have register both modules with different parameter in the initialization...
keil 5.12 could install pack file. I'd like to install S130 0.9 to keil 5.12, but I did not find S130 0.9 pack file. Could I install S130 0.9 manually and could select the...
Hi....
we are having some issues while testing our profiles in ios app.when switch from application to dfu am calling "sd_ble_gatts_service_changed(m_conn_handle,0x01,0x4D...
I'm looking for a simple and inexpensive solution for tying the TX and RX pins to GND after burning the OTP in production. What have other people done? I'd like to avoid having...
We are trying out nRF51822. My colleague has a top of the line Lenovo running Ubuntu and is able to detect the module when scanned. However, my macbook pro Mid 2014 (Which...
