Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi, I'm not used to the bsp.c so my question could be silly. I hope you could understand.
When I used SDK 6.1, the example about button_event_handler function had a parameter...
What is the best way to transfer an array of individual values using the BLE stack?
Is it by appending all the values into one blob and sticking it into a characteristic...
I'm using
HID keyboard example (SDK 7.2), Softdevice S110 7.1 , IAR for ARM 7.1, J-Link,
on my custom board (with NordicSemi nRF51822-QFAA MCU).
/***************...
I am designing a product with the nrf8002 chip and have a question on Power consumption. Lets say I leave all the default ratio's alone and use a CR1620 battery which has...
How can I read the Bluetooth clock (piconet) which is synchronized between the master/slaves in the piconet ? I need a constant (micro second accuracy) time from when I do...
Hello,
Is it possible to know the preamble , data format and the CRC calculation to interface a radio system ( GFSK Manchester) with NRF905 ?
Thank you
I'm wondering if the port and pin function can be used together to configure a set of pins.
For _port_dir_set, I assume it sets the whole port to the designated direction...
Hey i was using the code from developer.mbed.org/.../main.cpp
I am using this chip ( http://i.imgur.com/q8EM4uq.jpg ), it is nordic nRF51822 but i exactly do not know its...
I am using spi_master.c for spi communication with nRF51822EK.
And i had sent and recieved data packet successfully for 1st time with spi_master_send_recv(). When i sending...
Hi All,
I can compile and flash examples with my nrf51822 SDK on linux. I would like to use Code::Blocks as IDE.
Code::Blocks is transparent to run debugger. I try to...
I bought a blend micro to learn about arduino and BLE. I am a complete newbie in this field.
This is what I want to make happen,
I want to install my Blend Micro inside...
Hi All,
I am new in nrf51 development. I have a nRF51-DK kit. I would like to make development in Linux (Debian) only.
I found a lot of documents and I can compile examples...
My nRF Studio can not get nRF6130 board info,just show "Boards connected:".
But I can download fw to nRF51822 chip on the nRF6310 board.
The Application "ble_app_hrs" is...
What is the cleanest way to expose a dynamic (non-fixed amount of entries) through BLE?
One way I thought of is to create a service for a single table entry and go through...
Hi all,
I have an nRF-DK (the new one that's mbed compatible: developer.mbed.org/.../)
I have managed to completely brick it by copying the wrong file onto the BOOTLOADER...
