Dear Nordic Engineering Team,
I am currently developing a wireless ECG acquisition system based on the ADS1298 analog front end (AFE), the nRF5340 SoC, and the nRF7002 Wi...
Hi,
I believe 2M and 1M are OK to adjust, however, long range code added the extended advertisment, I am curious whether I can update these three PHY all together.
Thank...
Hi,
I was wondering if the newest sample available in NCS3.0.1 is already capable of holding multi connections. Otherwise, for this little time that is present i will...
Testing with NCS 3.0.1 and nRF54L15-DK. I would like my devices to be able to work as channel sounding initiator as well as reflector role. In my own code I have integrated...
Are there any samples for proprietary radio based on connect SDK?
https://www.nordicsemi.com/Products/Wireless/2-4-GHz-proprietary
I am not interested in gazelle and wanted...
Dears,
I have tried to install the nRF connect SW package on a Windows 7 32 bit system (different versions) but was not able to get the applications running. When installing...
Hi everyone, I'm working on a project with Zephyr (v2.9.1) and I'm facing a compilation issue related to managing two SPI devices on different buses ( spi0 and spi2 ).
In...
I am currently working on the secure_bootloader example (pca10056_s140_ble) for the nRF52840 DK board and am encountering an issue with updating the OTA application. I have...
Hello, I connected my (working) PPK2 and opened the PowerProfiler. Immediately, a "DFU needed" message popped up.
I DFUed the PPK2, and in the logs, it wrote DFU successfully...
Hello,
I'm currently working with the channel_sounding_ras_initiator project on the nRF54L15 DK , using the nRF Connect SDK from the latest main branch on GitHub ( nrfconnect...
What should be format of USER Certs for Matter factory data?
CONFIG_CHIP_FACTORY_DATA_CERT_SOURCE_USER =y
CONFIG_CHIP_FACTORY_DATA_USER_CERTS_DAC_CERT = "certs/Chip...
Hello, I have an application developed with the nRF9161 DK board, which essentially consists of a GPS tracker that acquires a position every x time and sends that same position...
Hi All.
I am trying to measure the consumption of the SoCs inside the nRF52840DK and the nRF52833DK using a PPK(II), both running the same code to make comparisons.
First...
hi support team,
i have customer is developping mesh.
customer is trying to sniffer the message when i pressed the buttoon on demo mesh_light.
i have two questions on...
NCS 2.9.1
NRF52840
Sysbuild but with only a single image (no bootloader)
I've been trying to figure out how to change the merged.hex output and how to perform additional...
Hi,
I was wondering if the newest sample available in NCS3.0.1 is already capable of holding multi connections. Otherwise, for this little time that is present i will...
Hi,the nordic Team.
I'm working on the thread protocol.and use the SDK version is V2.9.1.
I have a scenario where my child device is connected to a route or leader. What...
It might be due to a short circuit caused by incorrect wiring. The PPK2 circuit board is damaged, and the chip with silkscreen "L7 #247" in the lower-right corner seems to...
Hello,
we have a working system on the nrf9161 that works without zephyr. We have our own secure firmware that successfully uses the cc310 after we start the actual application...
Hello DevZone,
Is it possible to support Matter over Ethernet and Matter over Wi-Fi at same time?
Since there are many Ethernet chips support in Zephyr.
Seems that the...
When my mtd device is connected to a thread network, what should I do if I want to untie and join another thread network? How should I untie and clear the network information...
