Hello,
I am new to nRF development. I am going through the nRF Connect SDK Fundamentals course.
I wanted to configure a GPIO on the nRF52833 DK board as an output and...
It seems that I'm getting different results reading QSPI flash from the APP vs MCUBOOT, with the exact same configuration. Writes appear to work fine from either, but MCUBOOT...
I am trying to get the wifi stack to connect to a wifi AP using WAP2 Enterprise (initially just with identity and eap_password, later with full ca_certificate check and client...
I've got some timing-issues with the nPM2100. As I could not locate the relevant information in the datasheet, I'm requesting this here.
My PCB has an nPM2100 with a mechanical...
Hi,
i acheived writting code that reconnects sequentially with multiple reflectors for my 1 initiator. When i am indoor i had good results, but yesterday i tried it with...
Hello
I'm using an external flash to store large files, but I’d also like to use the SMP service to exchange small files over BLE. For that reason, I want to create a LittleFS...
HI ,ALL
i need to take use of the pstorage module.
i can read the data after reset,but i do not know the reason.
the write function is added in the on_write...
Hi there,
I have a nrf51422CEAA chip with 16k variant with single bank bootloader code. I compile it using (03) optimazation and the final result is :
"Program Size...
Hello,
I just produced my custom board with nRF52 but i have a problem.
I can program it (SWD over nRF52 DK), debug it (segger debudder software) but in bootloader it...
hi there,
I am using this tutorial to add dfu to nrf51422_xxac_s130 beacon application. however Im getting these linking errors:
._build\nrf51422_xxac_s130.axf: Error...
I was wondering what the procedure it for questions asked over the weekend. Obviously you guys are only available at office hours (Norway time I'm guessing?), so how do you...
I was kindly surprised with new S130 functionality - ECDH key exchange. Do you have plans in the near future to implement it in S110 softdevice? Thanks
Hi
I have nrf51822 CEAA which is powered with 1.9 volt on vdd (low power chip). I'm using ADC to measure battery level but the conversion gave me 5.4 volt wich is wrong for...
Hi,
we have developed some software that is running fine on the nRF52-DK (PCA10040 v0.9.0) which uses nRF52832 IC revision "Engineering B".
We are using SoftDevice s132_nrf52_2...
Hey everyone,
I am using nrf51 dongle pca 10031. Nordic promised to have 1Mbps data rate. when i was trying to transfer data through UART. data is validated until 401600...
hi
im working with nrf51422 and keil and s130
my external crystal is a 32768 and 16 mega
for my soft-device witch one should i use
// Initialize SoftDevice.
SOFTDEVICE_HANDLER_INIT...
I'm trying to add a characteristic to a service in nRFGo Studio with the Write propery enabled.
However, the software doesn't allow me to enable Write and greys the checkbox...
Hi,
i am using nrf51822 for my application.
i am using connectable undirected mode with 40 ms advertising interval but when i am seeing the device data in the nrf master...
hi,
i am using sdk 10, with s120.
i want to advertise data on a single channel with frequency say (2426).
is there any sample code or something, with which i can play...
Is there a hook anywhere in the SD (130/132) to let me generate my own LTKs, EDIV and RAND during the bonding process? I don't think so, I've not found one, but perhaps I...
Good afternoon.
I´m using nrf51-dk with SDK 9.0.0, s110 softdevice and uart nordic app on mobile. I have a program in my nrf51-dk that it sends and receives data between...
