Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I am using KDeveloper to program the nRF52, so far it has been working fine, but I want to be able ofdebugging and going into breakpoints, etc. What should I set in order...
I have programmed two boards(pca10056) with the cli example in thread sdk.I have set the first one as the leader and the second as the child but after pinging the kit the...
Hi guys,
I am working on a nrF52832 project and want to use Segger Embedded Studio since there is a license agreement for nordic based projects.
I am using freertos from...
Is it possible to communicate between 2 Nordic kits at 1 M baud without HW flow control? I came across this post in the forum which states that bytes can be missed when switching...
I am trying to use gcc to compile a c++ code for nRF52. I am using the TWI library and am getting the error below. Can anyone help me rewriting this macro so that it compiles...
Hello All,
I am using 32 pin nRF52810 chipset.
Crystal have two pin and it will work as in sch. (Xin and Xo)
when using Osc (which is an external clock generator) there...
Hello,
I'm trying to create a lightbulb custom HomeKit accessory by referring to the User Guide v1.7.1. I followed the exact same steps as described in the document for...
Hi,
* (i'am using sdk14.2 ans S140 V5.0.2)
i'am trying to inegrate a beacon application to my ble_uart example , so my purpose is to advertise ibeacon pachet format only...
We have some old stock of the nRF51822 pre 2014/8/20. Was there a change to the product around that time that would prevent us from using from using this stock?
Many th...
Hello,
I'm using FreeRTOS on nRF51 and I would like to use task notifications instead of semaphore to simply manage task's syncronization.
To test its operation mode,...
Hi, I just copied the antenna drawing by referencing the PCA10040 v1.1 and checking the white paper (λ/4 printed monopole antenna for 2.45 GHz) .
I didn't have much knowledge...
Hi,
How is the functionality of P0.21 in nRF52832? It is configured as RESET after turning on the device, right? Is there any way to change it in a way that that the chip...
Hello DevZone,
I am using a nRF52840 for project development.
To test SPI setting is correct or not, I am doing the loop-back test, I set the MISO and MOSI PIN according...
Hello,
I try to configure two nrf52832 devices work with payload of 200 bytes (data should be 200 bytes, not the all ble packet).
I took ble_app_uart_c peripheral and...
