nrf51822 SDK 9.0
iphone 6plus System version IOS9.2
When the phone receives the QQ message "static void notif_print(ble_ancs_c_evt_notif_t * p_notif);" can execute.
but...
Hi..... This is Venkatesh. I am using nRF52-DK Evaluation kit. This is my first question posting here. It is pleasure to have an account to share my knowledge and get the...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
I have created a device that will connect and pair with one central. I would like it to re-connect automatically after disconnecting because it was out of range or turned...
I can connect/pair/bond to the nrfConnect app and disconnect then reconnect just fine. When I try to do the same to a central running on arm bluez 5.43, the second and subsequent...
I am getting a SOFTDEVICE: ASSERTION FAILED after some time when advertising with whitelist. I am using NRF5_SDK 14.2.0 and have tried both softdevice s132 5.0.0 and 5.1.0...
Hi,
I am trying to use the fstorage lib in SDK 12.3.0. My code is based on this example: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5...
I'm sampling from the SAADC with a microphone attached and need to send the sampled data over ble to devices, and I want the devices to recognize the data as being a audio...
I need to develop a beacon application with the OTA DFU capabilities (Buttonless). I have the NRF51-DK.
As a starting point, I tried the bootloader example located in the...
Hi,
I'm designing a pcb for nrf52832, and acc. to specification sheet (2nd para under fig. 98) i need to use differential mode to avoid ground bouncing. Can I share a pin...
Hi DevZone,
I am going to implement Arduino CAN bus shield on nrf52840 preview DK. I am wondering if I can use the Arduino CAN bus library in the nrf52840 preview DK. As...
I'm using sdk 14.2 and I have nrf52832 board. Now when I go to armgcc folder in sdk of any example (I'm using the blinky example ) and open my command prompt and try to build...
Hello,
In SDK14.2, select an armgcc project, for example, pin_change_int.
For nRF52840, the heapsize is defined in /components/toolchain/gcc/gcc_startup_nrf52840.S,...
Hi,
I've compiled the pc-ble-driver-py library on a raspberry pi but it doesn't come with a "make install" command. Could someone help me get the right file structure so...
Hi,
I am looking library for EINK Epaper display. The display I am using is https://www.waveshare.com/wiki/1.54inch_e-Paper_Module
Can I get library code for this?
I have issue while building the nrf5 bluetooth mesh light switch example using CMake on windows for Eclipse. I have run the following cmake command:
cmake -G"Eclipse CDT4...
Using SDK 14.0.0 with an nRF52832, I'm trying to use the data length extension, following some sample code found in this post:
https://devzone.nordicsemi.com/f/nordic-q...
